Filter
Top Products
12
106813
PORTABLE GASOLINE GENERATORS
R
Figure 23 - Engine Switch In ON Position
(All Models Except MGH5000DIE,
MGH7000D, MGH10000A, and
MGH3000PR)
4. Start the engine.
A. Recoil Starter
Move engine lever or turn engine
switch to the ON position (see Figures
22 and 23). Remove slack from starter
rope by lightly pulling starter grip.
Next, pull starter rope briskly.
IMPORTANT:
Do not let starter grip
snap back against engine. Return it gen-
tly. This will prevent damage to starter.
Note:
If engine does not start, check
the oil in the crankcase. Add oil as nec-
essary. Be sure engine is on a level sur-
face. See Oil Alert System, page 6.
B. Electric Starter (Models
MGH5000DIE, MGH7000D,
MGH7000DI, and MGH10000A Only)
Turn the engine switch to the START
position (see Figure 24, page 13). Hold
it there until engine starts. When en-
gine starts, let switch return to the ON
position.
IMPORTANT:
Do not use electric
starter more than five seconds. Starter
motor damage may occur. If engine
fails to start, release the switch and wait
ten seconds. After ten seconds, try start-
ing again.
Note
: If engine does not start, check
the oil in the crankcase. Add oil as nec-
essary. Be sure engine is on a level sur-
face. See Oil Alert System, page 6.
5. As engine warms up, slowly move
choke lever fully to the right (see Fig-
ure 25, page 13). This opens the choke.
On Model MGH10000A, the choke
will automatically open.
ENGINE SW
ON
OFF
OPERATION
Continued
PRESTART
Operate generator on a firm, dry, and clean
surface. The surface must be level. Protect
generator from heavy dust, sand, dirt, rain,
or snow. Do not locate generator near stand-
ing water and snow. Make sure area is well-
vented.
WARNING: Only responsible
adults should use generator.
Never let anyone operate genera-
tor without proper instructions.
Note:
If oil level is too low, oil alert system
will keep engine from starting (see Oil Alert
System, page 6). Make sure oil level is full
before starting. See Engine Oil, page 7.
Before starting the engine, disconnect all
electric loads from generator.
STARTING
IMPORTANT:
The engine speed is preset.
The throttle is locked in preset position. Do
not adjust throttle. Preset position lets en-
gine run at 3600 RPM under load. The
engine must maintain 3600 RPM for gen-
erator to create correct voltage. Running
engine at lower speeds will damage genera-
tor and powered items.
IMPORTANT:
Never start generator with
electrical loads connected. Start engine be-
fore adding electrical loads.
1. Make sure gasoline tank is full. See
Fuel, page 7 for fuel information.
2. Move fuel valve lever to the ON posi-
tion except on Model MGH3000PR
(see Figure 19).
3. Move choke lever fully to the left for
all models except MGH3000PR or
MGH10000A (see Figure 19). Pull
choke rod out for Model MGH3000PR
(see Figure 20) or choke button out for
Model MGH10000A (see Figure 21).
This closes the choke.
Note:
You may not need to close choke
if engine is warm or air temperature is
high.
Fuel Valve Lever (ON Position)
Choke Lever (Closed Position)
Figure 19 - Fuel Valve Lever On, Choke
Lever Closed (Model MGH4000C Shown)
Figure 21 - Choke Button Closed (Model
MGH10000A Only)
Choke Button
Pulled Out
(Closed Position)
Figure 20 - Choke Rod Closed (Model
MGH3000PR Only)
Choke Rod
Pulled Out
(Closed
Position)
Figure 22 - Engine Lever In ON Position
(Model MGH3000PR Only)