Filter
Top Products
22
Gasoline
+
It is not wise to add more engine oil than specified
to ensure safe operation. This will only result in a
higher production of combus-tion residues which
will pollute the environment and clog the exhaust
channel in the cylinder as well as the muffler. In
addition, fuel consumption will rise and perform-
ance will decrease.
NOTE
:
Fuel cannot be stored for an unlimited period of time.
Buy only as much as will be consumed in 4 weeks.
Use only approved and marked containers for
transport and storage.
AVOID SKIN AND EYE CONTACT
Mineral oil products degrease your skin. If your skin
comes in contact with these substances repeatedly
and for an extended period of time, it will desiccate.
Various skin deseases may result. In addition, allergic
reactions are known to occur.
Eyes can be irritated by contact with oil. If oil comes
into your eyes, immediately wash them with clear
water.
If your eyes are still irritated, see a doctor immedi-
ately!
OIL
Chain oil
Use an oil with adhesive additive for lubricating the chain and
guide bar. The adhesive additive prevents the oil from being
flung off the chain too quickly.
We recommend the use of chain oil which is bio-degradable in
order to protect the environment. The use of bio-degradable oil
may even be required by local regulations.
The chain oil BIOTOP sold by MAKITA is made of special
vegetable oils and is 100% bio-degradable. BIOTOP has been
granted the "blue angel" (Blauer Umweltschutz-Engel) for
being particularly environment-friendly (RAL UZ 48).
E
BIOTOP chain oil is available in the following sizes:
1 l order number 980 008 610
5 l order number 980 008 611
Bio-degradable oil is stable only for a limited period of
time. It should be used within 2 years from the date of
manufacture (printed on the container).
50:1
40:1
D
Fuel
CAUTION:
This saw is powered by mineral-oil products (gasoline
(petrol) and oil).
Be especially careful when handling gasoline (petrol).
Avoid all flame or fire. Do not smoke (explosion hazard).
Fuel mixture
The engine of the chain saw is a high-efficiency two-stroke
engine. It runs on a mixture of gasoline and two-stroke engine
oil.
The engine is designed for unleaded regular gasoline with a
min. octane value of 91 ROZ. In case no such fuel is available,
you can use fuel with a higher octane value. This will not affect
the engine.
In order to obtain an optimum engine output and to protect
your health and the environment use unleaded fuel only.
Gasoline which contens alcohol should not used in
MAKITA products.
To lubricate the engine, use a high-performance two-stroke
engine oil (quality grade JASO FC or ISO EGD specifications),
which is added to the fuel. The engine has been designed for
use of MAKITA high-performance two-stroke engine oil and a
mixture ratio of only 50:1 to protect the environment. In addition,
a long service life and reliable operation with a minimum
emission of exhaust gases are ensured. MAKITA high-
performance two-stroke engine oil is available in the following
sizes to suit your individual requirements:
1 l order number 980 008 607
100 ml order number 980 008 606
In case MAKITA high-performance two-stroke engine oil is not
available, it is urgently recommended to use a mixture ratio of
40:1 with other two-stroke engine oils, as otherwise optimum
operation of the engine cannot be guaranteed.
The correct mixture ratio:
50:1 when using MAKITA high-performance two-stroke en-
gine oil, i. e. mix 50 parts gasoline with 1 part oil.
40:1 when using other two-stroke engine oils, i. e. mix 40
parts gasoline with 1 part oil.
NOTE:
For preparing the fuel-oil mixture first mix the entire oil quantity
with half of the fuel required, then add the remaining fuel.
Thoroughly shake the mixture before filling it into the chain saw
tank.
1.0 Us-gal. (3.7 l) 2.5 floz. (75 cm
3
) 3.2 floz. (94 cm
3
)
2.5 Us-gal. (9.4 l) 6.4 floz. (189 cm
3
) 8.0 floz. (236 cm
3
)
5.0 Us-gal. (18.9 l) 12.8 floz. (378 cm
3
) 16.0 floz. (473 cm
3
)
OIL
50:1