Filter
Top Products
Operator's Manual 9
Reference #2 Decal: Caution-Allow to Cool (Part #34-0599)
Reference #3 Decal: Warning-Mufer Hot (Part #34-0598)
Reference #13 Decal: Warning: Risk of Injection (Part #34-1253)
Reference #4 Decal: Warning/Caution/Operating Instructions (Part #34-1883)
SAFETY DECALS & PLACEMENT FOR HR-2410GH
DO NOT REMOVE SAFETY DECALS FROM UNIT
UNLESS REPLACING WITH MOST CURRENT SAFETY DECAL!!!
RISK OF BURNS
MUFFLER AND
ADJACENT AREAS
MAY EXCEED 150°F.
RIESGO DE QUEMAR
EL AMORTIGUADOR Y LAS
AREAS ADYACENTES PUEDEN
TENER TEMPERATURAS POR
ARRIBA DE 150°F.
34-0598-010699-E/S-ENG.
WARNING
ADVERTENCIA
34-0599-E/S-030600-ENG
No ponga combustible cuando
el producto este en operacion.
Permita que el motor se enfrie
por 2 minutos antes de
reablastecer de combustible.
RISK OF FIRE
Do not add fuel when
product is operating. Allow
engine to cool for two (2)
minutes before refueling.
RIESGO DE FUEGE
CAUTION/PRECAUCION
WARNING
CAUTION
• Risk of Injection or Severe Injury: Keep clear of
nozzle. Do not direct spray toward any person or
self.
• Risk of Asphyxiation: Outdoor use only required.
• Risk of Fire: Do not smoke while refueling. Allow to
cool two to three minutes before refueling. Do not
operate while refueling.
• Risk of Electrocution: Do not direct spray toward
any electrical connections, outlets or power lines.
• Risk of Explosion: Do not spray flammable liquids.
• Risk of Injury: Use only properly rated equipment.
• To Reduce Risk of Injury: Read and understand
the operation manual and all instructions before
using.
• Stay Alert: Hold on to gun/wand firmly with both
hands to avoid dangerous kickbacks.
• Always wear eye protection.
• Do not over-reach or stand on unstable support.
Keep good footing and balance at all times.
• Always turn on water supply to pump before
starting.
• Protect pump from freezing.
• Engage trigger safety lock-off when not in use.
OPERATION
• After ensuring all connections are secure, open
inlet water supply completely. Do not operate
without water. Do not use water that is over
70°F/21°C.
• Point gun in a safe direction and adjust nozzle to
low pressure. Brace wand securely to avoid recoil.
Squeeze trigger open and steady the unit while
starting. Start the unit by firmly pulling starter rope.
• After engine is running, adjust the nozzle to
desired setting, squeeze trigger to spray and
release the trigger to stop spray.
• After stopping the engine, always turn off water
supply and squeeze trigger to release trapped
pressure.
34-1883-102506-ENG.
PART #: 34-1883
ARTWORK: 100% 10.23" x 2.85"
UL recognized (PGDQ2) marking/labeling system.
CSA Accepted marking/labeling system.
Suitable for the surface to which they are applied (below):
Suitable for exposure to water and outdoor use.
Temperature range: -40°C to 70C.
Base Material: .002"-.004", Polyester, Vinyl, Mylar
Over Laminate: .001" Clear Laminate
Adhesive: Must Adhere to Polyester and epoxy powder coatings, epoxy paint
polypropylene, polyethylene and stainless steel surfaces.
Backing: Center Split Back
Corners: .25
Warning: Ansi Orange w/ Black Text Arial 24pt. Bold
Caution: Ansi Yellow w/ Black Text 24pt. Arial Bold
Operation: White w/ Black Text 24pt Bold
Text Panel: Black w/White Text Arial Bold 10pt.
Saved in Adobe Illustrator CS2 MI-T-M Artwork
Questions?? Contact Nicole Davis 556-7484 Ext. 267
RISK OF INJECTION OR SEVERE INJURY.
Never put your hand, fingers or body directly
over the spray nozzle.
34-1253-030801-ENG.
WARNING
ADVERTENCIA
RIESGO DE INYECCION O LISION SEVERA
Nunca coloque la mano, los dedos o el cuerpo
directamente sobre la boquilla de rocío.