Filter
Top Products
Net engine power is with standard equipment including air
cleaner, exhaust system,alternator, and cooling fan,at stan-
dard conditions per SAE J1349 and DIN 70 020,using No. 2-D
fuel at 35 API gravity. No derating is required up to 5,000-ft.
(1500 m) altitude. Gross power is without cooling fan.
Specifications and design subject to change without notice.Wherever applicable, specifications are in accordance with SAE
and/or ISO standards. Except where otherwise noted,these specifications are based on a unit with 16.9-24,8 PR R4 rear tires;
12-16.5, 8 PR NHS front tires; 1.00-cu.yd. (0.76 m
3
) loader bucket; full fuel tank; and 175-lb. (79 kg) operator.
210LE
Engine
●
Meets EPA and CARB emission non-road regulations
● John Deere Model 4045D – 4.5 liter,73 SAE net hp
naturally aspirated, isolation mounted
▲ John Deere Model 4045T – 4.5 liter, 80 SAE net hp
turbocharged,isolation mounted
● Diagnostic capabilities with Tier-IIengine
● Vertical spin-on engine oil filter
● Spin-on John Deere fuel filter
● Oil-to-water engine oil cooler
● Antifreeze,–34°F (–37°C)
● Coolant recovery tank
● Serpentine belt with automatic belt tensioner
● Sucker-type cooling fan
● Enclosed safety fan guard
● Dual element dry-type air cleaner with evacuator
valve and prescreener
● Muffler,underhood with curved-end exhaust stack
▲ Muffler, spark arrested,underhood with curved-end
exhaust stack
▲ Electric ether starting aid
▲ Engine coolant heater,1,000 watts
Power Train
●
Transmission with powershift reverser and torque
converter:Fully synchronized four forward, four
reverse speeds / Isolation mounted to mainframe
▲ Powershift transmission:Torque converter with
electrically actuated twist grip F-N-R in 1st through
4th gears
● Transmission oil cooler
● Vertical spin-on transmission filter
● Electric forward-neutral-reverse control lever with
neutral safety switch interlock
● Electric clutch cutoff on gearshift and loader levers
● Differential lock,electric foot-actuated
● Planetary final drives
● Hydraulic service brakes (conform to SAE J1473):
Inboard,wet multi-disc, self adjusting and self equal-
izing
● Parking brake with electric switch control (conforms
to SAE J1473):Spring applied,hydraulically released
wet multi-disc / Independent of service brakes
● Hydrostatic power steering with emergency manual
mode
● MFWD axle
● Mechanical-front-wheel-drive,standard differential:
Electric on/off control / Driveshaft guard / Sealed axle
▲ Mechanical-front-wheel-drive,limited-slip differential:
Electric on/off control / Driveshaft guard / Sealed axle
▲ Transmission guard
▲ Rear wheel spacers for use with chains*
210LE
Three-Point Hitch
●
Integral Category II
● Four-function sectional hydraulic valve,6 gpm: Lift,
with down-pressure and float / Tilt, single / Pitch /
Fourth function auxiliary with capped hoses
● Cylinders:Lift (1) / Tilt (1) / Pitch (1)
▲ Fifth-function auxiliary valve with control lever
▲ Hydraulic flow cartridge,3 gpm*
▲ Second tilt cylinder
Loader
●
Hydraulic self leveling
● Return-to-dig feature
● Single-lever control with electric clutch cutoff switch
● Bucket-level indicator
● Loader boom service lock
▲ Loader front coupler
▲ Third-function valve and lever for auxiliary equipment
Hydraulic System
●
25 gpm (95 L/min.) gear pump,open center system
● Independent hydraulic reservoir
● Hydraulic oil cooler
● “O”-ring face seal connectors
● 10-micron vertical spin-on filter
Electrical
●
12-volt system
● 65-amp alternator
● Single battery with 180-min. reserve capacity and
925 CCA
▲ Dual batteries with 360-min.reserve capacity and
1,850 CCA
● Positive terminal battery cover
● Blade-type multi-fused circuits
● By-pass start safety cover on starter
Lights
●
Two front halogen driving/work lights,32,500 candle-
power each
▲ Deluxe electrical package with rear lights,light guards
for front and signal lights,two 12-volt convenience
outlets,and battery disconnect switch
● Two combination front/rear turn signal/flashing
● Two rear stop and tail
● Two rear reflectors
▲ Rotating beacon*
Operator’s Station
●
Two-post ROPS/FOPS canopy with steel roof (conforms
to SAE J1040):Isolation mounted
▲ Operator enclosure*
● Left front access
● Slip-resistant steps and ergonomically located
handholds
● Built-in Operator’s Manual storage compartment with
manual
210LE
Operator’s Station
(continued)
● Interior rearview mirror
● Foot throttle
▲ Hand throttle
● Horn
● Key start switch with electric fuel shutoff
● Hourmeter, electric
● Fuel gauge,illuminated electric
● Hydraulic self leveling
● Monitor system with audible and visual warning:Engine
air filter restriction indicator / Alternator indicator /
Engine coolant temperature indicator with audible
warning / Engine oil pressure indicator with audible
warning / Hydraulic filter restriction indicator / Torque
converter oil temperature indicator / Parking brake
on/off indicator with audible warning / Seat belt indi-
cator / Mechanical front-wheel-drive on/off indicator
● Suspension vinyl seat with flip-up armrests, backrest
angle adjustment,swivel base, 3-in.seat belt with
retractor
▲ Non-suspension vinyl seat without armrests, with
3-in.seat belt with retractor
Loader Buckets
●
Less bucket,with bucket pins
▲ Heavy-duty bucket with lift loops,prepunched for
bolt-on cutting edge
▲ Heavy-duty buckets with bolt-on cutting edge,skid
plates, and lift loops
▲ Multipurpose buckets with bolt-on cutting edge,skid
plates, and lift loops
Tires
▲
12-16.5,8 PR NHS front tires
● 16.9-24,8 PR R4 rear tires
Overall Vehicle
●
One-piece unitized construction mainframe with
integral front bumper
● Vehicle tiedowns, two front and two rear
● Fuel tank,26 gal. (98 L),ground level fueling
● Vandal protection for instrument panel,access doors,
fuel tank,and hydraulic reservoir
● Reverse warning alarm
● Dent-resistant rear fenders
▲ Three-point hitch counterweight
▲ Wheel weights
▲ Hydrostatic PTO,540 rpm
▲ Three-point hitch weight box*
▲ Drawbar,fixed single position
▲ Box scraper
(contact Cameco Industries for ordering
information and factory installation)
▲ SMVemblem*
▲ Brush guards*
▲ Fender extensions*
▲ Cab panels*
210LE LANDSCAPE LOADER
Key: ● Standard equipment ▲ Optional or special equipment *See your John Deere dealer for further information.
DKA210LE Litho in U.S.A. (05-08)
Customer Personal Service (CPS) is part of John Deere’s proactive,fix-before-fail strategy on machine
maintenance that will help control costs, increase profits,and reduce stress.Included in this comprehen-
sive lineup of ongoing programs and services are:
Fluid analysis program—
tells you what’s going on inside
all
of your machine’s major components
so you’ll know if there’s a problem
before
you see a decline in performance.Fluid analysis is included in
most extended coverage and preventive-maintenance agreements.
Component life-cycle data—
gives you vital information on the projected life span of components
and lets you make informed decisions on machine maintenance by telling you approximately how many
hours of use you can expect from an engine,transmission, or hydraulic pump.This information can be used
to preempt catastrophic downtime by servicing major components at about 80 percent of their life cycle.
Preventive Maintenance (PM) agreements—
give you a fixed cost for maintaining a machine for
a given period of time.They also help you avoid downtime by ensuring that critical maintenance work gets
done right and on schedule.On-site preventive maintenance service performed where and when you need
it helps protect you from the expense of catastrophic failures and lets you avoid waste-disposal hassles.
Extended coverage—
gives you a fixed cost for machine repairs for a given period of time so you
can effectively manage costs.Whether you work in a severe-service setting or just want to spread the
risk of doing business,this is a great way to custom-fit coverage for your operation.And an extended
coverage contract also travels well because it’s backed by John Deere and is honored by
all
Deere
construction dealers.
Customer Support Advisors (CSAs)—
Deere believes the CSA program lends a
personal
quality to
Customer Personal Service (CPS).Certified CSAs have the knowledge and skills for helping make important
decisions on machine maintenance and repair.Their mission is to help you implement a plan that’s right
for
your
business and take the burden of machine maintenance off your shoulders.
CONTROL OWNING AND OPERATING COSTS
DKA210LE Page 12
Vertis QCA
1300 19th Street, Suite 200
East Moline, IL 61244
Cyan
Magenta
Yellow Black
DKA210LE_SPECS 9/19/05 11:16 AM Page 12