Filter
Top Products
766238 6/07 7-9
Clutch Assembly
NOTES:
1. Tighten nut enough to allow free movement of item 9, clutch lever.
2. Lubricate with grease before assembly.
3. Position item 18, pivot bracket, with large hole on top.
4. Make sure item 28, idler arm, moves freely by tightening item 13, nut,
until it clamps idler arm so that it cannot move. Then back nut off
(loosen) until idler arm moves freely.
5. Pump clutch lever must break over center and hold.
INDEX
NO.
SERVICE
PART NO.
MFG. PART
NO.
QTY. DESCRIPTION
1 387027 387027 1 CLUTCH LINKAGE
2 384826 384826 1 CLUTCH MOUNT
3 072611 072611 1 FW .406 X .812 X .065 BO
4 017251 017251 2 CP .156D X 1.00 LG HML ZN
5 064014 064014 2 CS .312-18 X .875 HX G5 ZN
6 017004 017004 2 LW .312 MEDIUM SPRING ZN
7 049346 049346 2 FW .375 X .870 X .078 ZN
8 015495 015495 1 GREASE FITTING
9 384834 384834 1 CLUTCH LEVER
10 074559 074559 1 HAND GRIP
11 016428 016428 1 CS .375-16 X 2.50 HX G5 ZN
12 017012 017012 1 LW .375 MEDIUM SPRING ZN
13 046763 046763 2 NT .375-16 FLEX-LOK ZN
14 447557 447557 1 CLUTCH LEVER LINKAGE
15 025403 025403 1 FW .281 X .625 X .062 ZN
16 017236 017236 2 CP .093D X .750 LG HML ZN
17 073866 073866 1 FW .281 X .50 X .060 ZN
18 385922 385922 1 PIVOT BRACKET
19 080838 080838 1 CLUTCH SPRING
20 754937 754937 1 FW .406 X 1.250 X .080 ZN
21 063297 063297 1 SB .370 X .50 SH .312-18 TD
22 460634 460634 1 CLUTCH PIVOT ARM
23 704718 704718 1 FW .406 X .688 X .060 ZN
24 712281 712281 2 NT .312-18 HX FLK
25 060541 060541 1 SB .50 X .625 SH .375-16 ZN
26 058875 058875 1 MB .510 X .870 X .050 ZN
27 706168 706168 1 NT .375-16 HX JAM G5 ZN
28 386391 386391 1 IDLER ARM
29 722678 722678 1 SB .375 X .620 SH .312-18 TH ZN
30 704726 704726 1 FW .406 X 1.00 X .105 ZN
31 016444 016444 1 CS .375-16 X 3.00 HX G5 ZN
32 070672 070672 1 NT .375-16 HX FL CLK ZN
33 736520 736520 1 CS .375-16 X 5.250 HX G5 ZN
34 388074 388074 1 IDLER SPACER
35 534396 534396 1 IDLER PULLEY
36 388082 388082 1 IDLER SPACER