SAFETY PRECAUTIONS
Use
1. Use the lawnmower only in daylight or good
artificial light.
2. Avoid operating your lawnmower in wet grass,
where feasible.
3. Take care in wet grass, you may lose your footing.
4. On slopes, be extra careful of your footing and
wear non-slip footwear.
5. Mow across the face of slopes, never up and down.
6. Exercise extreme caution when changing
direction on slopes. Walk never run.
7. Mowing on banks and slopes can be dangerous.
Do not mow on banks
or steep slopes.
8. Do not walk backwards when mowing, you could trip.
9. Never cut grass by pulling the mower towards you.
10.Switch off before moving the lawnmower across
surfaces other than grass and when transporting
the lawnmower to and from the area to be
mowed.
11.Never operate the lawnmower with damaged
guards or without guards in place.
12.Keep hands and feet away from the cutting
means at all times and especially when switching
on the motor.
13. Do not tilt the lawnmower when the motor is running,
except when starting and stopping. In this case, do
not tilt more than absolutely necessary and lift only
the part which is away from the operator. Always
ensure that both hands are in the operating position
before returning the appliance to the ground.
14.Do not put hands near the grass discharge chute
whilst the motor is running.
15.Never pick up or carry a lawnmower when it is
operating or still connected to the mains.
16.Remove the plug from the mains :
- before leaving the mower unattended for any
period;
- before clearing a blockage;
- before checking, cleaning or working on the
appliance;
- if you hit an object. Do not use your lawnmower
until you are sure that the entire lawnmower is in
a safe operating condition;
- if the lawnmower starts to vibrate abnormally.
Check immediately. Excessive vibration can
cause injury.
Maintenance and storage
1. Keep all nuts, bolts and screws tight to be sure
the lawnmower is in safe working condition.
2. Check the grassbox/grassbag frequently for wear
or deterioration.
3 Replace worn or damaged parts for safety.
4. Only use the replacement blade, blade bolt,
spacer and impeller specified for this product.
5. Be careful during adjustment of the machine to
prevent entrapment of the fingers between
moving blades and fixed parts of the machine.
ASSEMBLY INSTRUCTIONS
ROYAL 36EL
Fitting the Lower Handle to your Lawnmower
1. Pull the tie spindle bar (A1) to one side so that it
is flush with hole in the side of the moulding.
2. Locate the lower handle formed end in the
recessed moulding at the rear of the deck (A).
3. Insert the nut into the handle knob (if applicable).
4. Push the tie bar back through the locating hole in
the handle and secure it with a handle knob (A).
5. Repeat the sequence for the other side of the
handle.
Fitting the Upper Handle to the Lower Handle
1. Make sure the switchbox is on the right hand
side when viewed from the rear.
2. Insert the nut into the handle knob (if applicable).
3. Fit the bolts, washers and handle knobs (B).
4. Fit the cable to the handles with the clips
provided making sure the cable is not trapped
between the upper and lower handles.
ROYAL 43EL/ELS
Fitting the Lower Handle to your Lawnmower
1. Secure the lower handle with the handle knobs
provided. Make sure the end of the handle is
properly located in the lawnmower (C).
Fitting the Upper Handle to the Lower Handle
1. Make sure the switchbox is on the right hand
side when viewed from the rear.
2. Fit the bolts, washers and handle knobs (D).
3. Fit the cable to the handles with the clips
provided making sure the cable is not trapped
between the upper and lower handles.
Grassbox Assembly
Assembling the Grassbox Screen
1. Fold the screen sides inwards (E1).
2. Align the matching tabs and slots in the back and
sides of the grassbox screen and press firmly
together (E2).
3. The assembled screen should appear as
illustrated (E3).
4. Lower the assembled screen into the grassbox,
aligning the tabs with the slots in the grassbox
and press firmly together (E4, E5).
5. Take the lid, align the tabs with the slots and
press firmly together (E6).
Fitting Fully Assembled Grassbox to Lawnmower
1. Lift safety flap. Make sure the discharge chute is
clean and free from debris.
2. Locate fully assembled grassbox onto grassbox
sill.
3. Fit the 2 location studs on the safety flap into the
2 location holes on the grassbox lid and ensure
the grassbox is securely located (F).
IMPORTANT
After fitting ensure no gap remains between the
safety flap and grassbox lid.
4. Removal is the reverse procedure
Where grass collection is not required you can
use the lawnmower without the grass collector.
Ensure the safety flap is fully closed.
ENGLISH - 2