Flymo XL550 Lawn Mower User Manual


 
Fitting the Blade and the Fan
Before using the lawnmower, always visually
inspect to see that blades and bolts are not
worn or damaged.
Never use more than 2 cutting height
spacers.
Spacers can only be fitted between the blade
and the fan and never between blade and the
bolt.
1. Ensure the fan is located correctly.
2. Place the spacers (P3) onto the fan ensuring the
pegs (P5) have located into the holes (P6).
3. Place the blade (P2) onto the spacers (P3)
ensuring the pegs (P7) have located into the
holes (P8) on the blade and ensuring the blade
is positioned as illustrated in Figure P.
4. Place the blade bolt (P1) through the centre hole
(P9) of the blade.
5. Tighten down clockwise by hand.
6. Hold the fan firmly and tighten the blade bolt
with the spanner provided.
Removing & Fitting the Blade & Fan
Caring for your Lawnmower
If you do not intend to use your lawnmower for
long periods it is advisable to follow this
procedure after use:
1. Stop the engine.
2. Fully close the fuel tap. (K)
3. Restart the engine.
4. As fuel runs out the engine will begin to stop, tilt
the lawnmower slightly.
5. Once the engine has stopped, release the
Operator Presence Control.
6. Disconnect the spark plug lead.
7. Remove all fuel from the fuel tank.
Cleaning - USE GLOVES
Keep your lawnmower clean - grass clippings
left in any of the air intakes, around the
engine or under the deck could become a
potential fire hazard.
Do not clean with chemicals, including petrol, or
solvents - some can destroy critical plastic
parts.
1. Remove grass from under the deck with a piece
of wood or similar.
2. Using a soft brush - remove grass clippings from
around the engine and from all air intakes.
3. Remove the fan, See 'Removing and Fitting
the Blade and Fan', and clean with a soft
brush.
4. Wipe over the surface of your lawnmower with a
dry cloth.
Transporting your Lawnmower
Turn the fuel tap to the off position and transport
with the engine in a horizontal position.
Never transport the lawnmower when it is
running.
Storing Your Lawnmower
Turn the fuel tap to the off position and store in a
cool, dry, damp-proof and safe place with the
engine in a horizontal position. Service your
lawnmower after the last cut of the year as follows:-
At the end of the Mowing Season
1. Stop the engine.
2. Fully close the fuel tap. (K)
3. Restart the engine.
4. As fuel runs out the engine will begin to stop, tilt
the lawnmower slightly.
5. Once the engine has stopped, release the
Operator Presence Control.
6. Disconnect the spark plug lead.
7. Remove all fuel from the fuel tank.
8. Remove the spark plug lead and spark plug. Pour
one teaspoon (5ml) of oil through the spark plug
hole. Pull the starting handle 2 or 3 times. This will
distribute oil on the internal surfaces of the engine.
Inspect, clean and replace the spark plug. If a new
spark plug is required contact your local approved
Electrolux Outdoor Products Service Centre/Dealer.
Do not re-connect the spark plug lead.
9. Clean the air filter. See 'Cleaning the Air Filter'.
10.Renew the blade if it is cracked, damaged or
bent. Renew the blade bolt if necessary. See
'Removing and Fitting the Blade and Fan' for
complete instructions.
11.Use only genuine Flymo parts and accessories
specified for this product.
12.Clean your lawnmower thoroughly See 'Cleaning'.
13.Your local approved Electrolux Outdoor
Products Service Centre/Dealer will carry out
any service or repairs required.
14.Store your lawnmower in a cool, dry, damp-proof
and safe place.
Cleaning the Air Filter
Q1 - Air Duct
Q2 - Air Cleaner Body
Q3 - Filter
Q4 - Latch Tabs
Q5 - Air Cleaner Cover
Never run the engine without a filter or with a dirty
filter. This will greatly reduce engine efficiency and
lead to engine damage.
Your lawnmower is fitted with an Air Cleaner, the
maintenance for which is as follows:-
Check the filter before each use.
Clean every 25 hrs or more frequently when
used in dusty areas.
Replace filter every 200 hrs.
1. Press the latch tabs on the top of the air cleaner
cover and remove the cover.
2. Check the filter is clean and in good condition.
If the filter is dirty:-
Tap the air filter several times on a hard surface
to remove dirt, or blow compressed air through
the air filter from the clean side that faces the
engine. Never try to brush off dirt. Brushing will
force dirt into the fibers.
3. Wipe dirt from the air cleaner body and cover
using a moist rag. Be careful to prevent dirt
from entering the air duct that leads to the
carburetor.
4. Replace the filter and air cleaner cover.
Spark Plug
An oily or carboned spark plug makes starting
difficult and decreases the efficiency of the engine.
Periodically remove the spark plug and clean and
adjust when necessary.
Gap setting 0.028 - 0.031".
Do not remove spark plug when engine is hot. Do
not sand blast the spark plug to clean it.
ENGLISH - 4