Flymo 360XC Lawn Mower User Manual


 
Environmental Information
Husqvarna UK Ltd. products are manufactured under an
Environmental Management System (ISO 14001) using,
where practical, components manufactured in the most
environmentally responsible manner, according to
company procedures, and with the potential for recycling
at the end of the products’ life.
Packaging is recyclable and plastic components have
been labelled (where practical) for categorised recycling.
• Awareness of the environment must be considered
when disposing of ‘end-of-life’ product.
• If necessary, contact your local authority for disposal
information.
The symbol on the product or on its packaging indicates
that this product may not be treated as household waste.
Instead it shall be handed over to the applicable collection
point for the recycling of electrical and electronic equipment.
By ensuring this product is disposed of correctly, you will help
prevent potential negative consequences for the environment
and human health, which could otherwise be caused by
inappropriate waste handling of this product. For more detailed
information about recycling of this product, please contact your
local council office, your household waste disposal service or
the shop where you purchased the product.
Fault Finding Hints
Fails to Operate
1.Is the correct Starting procedure being followed? See
‘To Start your Lawnmower’
2.Is the Power Turned On?
3.Check the fuse in the plug, if blown replace.
4.Fuse continues to blow?
Immediately disconnect from the mains electricity supply
and consult your local approved Service Centre.
Poor Grass Collection
1.Disconnect from the mains electricity supply.
2.Clean the outside of the air intakes, the discharge
chute and the underside of the deck.
3. Raise to a higher height of cut. See Cutting Height Adjustment.
4.If poor collection persists.
Immediately disconnect from the mains electricity supply
and consult your local approved Service Centre.
Excessive Vibration
1.
Disconnect from the mains electricity supply.
2.Check that the blade is fitted correctly?
3. If the blade is damaged or worn, replace it with a new one.
4.If vibration persists?
Immediately disconnect from the mains electricity supply
and consult your local approved Service Centre.
Lawnmower becomes heavy to push
1.Disconnect from the mains electricity supply.
2.In long grass or uneven ground, the height of cut
should be raised to a higher position. See Cutting
Height Adjustment.
3. Check that the wheels and rollers can rotate freely.
4.If problem persists?
Immediately disconnect from the mains electricity supply
and consult your local approved Service Centre.
Service Recommendations
1. We strongly recommend that your product is serviced
at least every twelve months, more often in a
professional application.
2. Always use genuine Spare Parts.
3. Prepacked spares are available from most Husqvarna
Outdoor Products stockists.
4. Your product is uniquely identified by a silver and
black product rating label
5. If you have a problem with your machine contact your local
Approved Service Centre ensuring you have full details of
your product as described on the product rating label.
6. Should it be necessary for work to be carried out by
your Service Centre, it is important to take your
complete machine including cable and any extension
cables used.
A network of specialist dealers can be found in your local
Yellow Pages. To obtain service on your product simply
telephone or visit your local Service Centre. Should you
require service under the terms of our guarantee the Service
Centre will require proof of purchase.
All of the centres listed stock genuine Spare Parts.
NOTE: Our Service Repairers act on their own behalf
and are not empowered to commit or legally bind
Husqvarna UK Ltd. in any manner whatsoever.
PAGE 10
Easi-Reel Cable Winder (XC models only)
Storing your cable in the Easi-Reel cable winder
1. Insert the female connector into the centre of the
cable winder (Y1)
2. Place the cable under the cable guide (Y2)
3. Turn the cable winder (Y3) until all of the cable is
wound in.(Y4)
Unwinding the cable before re-use
1. Pull the cable by the plug and unwind the cable fully.
Ensure that the cable is released from the cable guide
(Y2) before using your machine.
Ensure cable is not entangled with any other cables
and that it is not trapped in any parts of the product.
Y1 Y2
Y3 Y4