Filter
Top Products
Assembling the Pressure Washer
OPERATING INSTRUCTIONS
Attaching High Pressure Hose to
Pressure Washer
Garden Hose Connection
2. Then attach the other end of the high
pressure hose to the high pressure
hose connector on the trigger gun.
(Fig. 9)
Fig. 9
3. Once the high pressure hose is
connected to the trigger gun, you can
attach any of the lances and
accessories that you desire. To
attach either of the lances or the
brush to the trigger gun, hold the
trigger gun in your left hand insert the
desired lance or the brush and push
it in all the way into the connector on
the trigger gun and turn it clockwise
60° until it locks in place. To remove
the attachment, push down on the
attachment and turn counter-
clockwise 60° and then pull out.
Make sure that the attachments are
securely locked in place before use.
(Fig. 10)
Fig. 2
Fig. 3 Fig. 4 Fig. 5
Fig. 6
Fig. 7
1 1/4”
SCREW
7/8”
SCREW
7/8”
SCREW
1. Carefully take all the parts out of the
packaging container and place
together on a flat, stable surface.
2. Insert the wheels onto the wheel
axle and push in the wheel lock to
lock the wheels in place. (Fig. 2)
3. Turn the pressure washer upside
down and slide the front support
onto the unit. (Fig 2)
4. Using the 1” long nickel plated
screw, secure the front support to
the unit.
1.
2.
5
Attaching The Wheels To The
Pressure Washer
Once all the desired attachments and
the high pressure hose are attached to
the pressure washer, you can connect
the garden hose to the unit.
1. Make sure that the water intake filter
is inside the water intake inlet.
(Fig. 11)
2. Attach the male adapter (supplied)
to the water intake connector on the
front side of the unit. (Fig. 11)
3. Attach the female hose coupling to
the garden hose. (Fig. 11)
4. Connect the female hose coupling
to the male adapter making sure
that it is tightly secured in place.
(Fig. 11)
Once the pressure washer is assembled,
you are ready to use the unit.
1. While facing the rear of the unit
attach the high pressure hose to the
high pressure output connector on
the back side of the unit. Twist on
tight to avoid leakage. (Fig. 8)
Fig. 8
Fig. 11
Water inlet
Water intake
filter
Garden hose
(not supplied)
Hose
connector
Garden hose
coupling
4. After all the connections have been
and
BEFORE you plug the pressure
washer into an electrical outlet, open
the water supply and press on the
trigger switch in order to remove any
air which may be in the hose or
pump. Continue to press on the
trigger switch until you get a constant
flow of water coming out of the trigger
gun. Allow water to flow for 30
seconds.
5. Once this is accomplished, stop
pressing the trigger switch. Engage
the safety lock on the trigger
6. Ensure that the "On/Off" switch, at
the side of the unit, is on the "Off"
position, then plug the unit into an
electrical outlet and turn the unit to
the "On" position.
7. Now you are ready to use the
pressure washer. Disengage the
safety lock and depress the trigger on
the trigger gun.
Attaching The Handle To The
Pressure Washer
Place the handle on the unit as
shown in Fig. 3.
Push the handle in at the bottom
until it is in position. See Fig. 4.
3. Let the handle slide down to its
resting place as shown in Fig 5 & 6.
4. To secure the handle to the unit,
screw 1 1/4” screw at the top hole
and the two (2) 7/8” screws on each
side of the handle. See Fig. 7.
Fig. 10
6