Filter
Top Products
GETTING TO KNOW YOUR PRESSURE WASHER OPERATING INSTRUCTIONS
1. Pressure Washer
2. Water Intake
3. Water Intake Filter
4. On/Off Switch
5. Handle
6. Detergent Tank
7. High Pressure Output
8. Power Cord
9. Wheels (x2)
10. Wheel Locks (x2)
11. Front Support
12. Adjustable Fan Jet Lance
13. high pressure lance
14. Trigger Gun
15. Trigger
16. Trigger Lock
17. High Pressure Hose Connector
18. Brush
19. High Pressure Hose
20. 13-ft Drain Snake (For outdoor use
ONLY)
21. Hose Connector
22. Garden Hose Coupling
23. Phillips Screw 1 1/4–inch long (x1)
(not shown)
24. Phillips Screw 7/8-inch long (x2)
(not shown)
25. Phillips Screw 1-inch long (x1 nickel plate)
(not shown)
Technical Specifications
Voltage: 120V., 60Hz.
Power: 13 Amps
Pressure: 1750 psi. (max)
Flow Rate: 1.65 GpH
Illustrations may differ from actual product.
3
Cleaning the Nozzles: If you notice that the
output pressure fluctuates, you may have to
clean the nozzles. Turn the unit "Off". Unplug
from electric outlet and disconnect the water
supply. Remove the lances, trigger gun and
hose from unit. Take the small metal pin
provided and insert into the nozzle end to
remove any obstructions. (Fig. 19)
Fig. 19
This will occur more frequently if your
water supply is very hard.
Lubrication: The pressure washer is
supplied with a closed lubrication system,
so no addition of oil is needed.
Checking the Water Intake Filter
: The water
intake filter is located inside the water intake
connector. (Fig. 18). Remove periodically
and inspect for any deposits that might
accumulate there.
Fig. 18
Hose Connector
Water Intake
Maintenance & Cleaning Winterizing & Long Term Storage
1. Disconnect all water connections.
2. Turn the pressure washer on for a
few seconds, until any remaining
water in the pump exits.
3. Turn the unit off immediately.
4. Store the pressure washer, parts
and accessories in an area with a
temperature above 32°F.
Motor Thermostat
Important: This pressure washer is
equipped with a motor thermostat. The
motor will stop if it is overheating. Wait
10-20 minutes before starting the unit
again. If it stops again, please call
FANTOM customer service at
1-800-798-7398.
Ground Fault Circuit Interrupter
(GFCI)
This unit is equipped with a Ground
Fault Circuit Interrupter (GFCI) built
into the plug. This device provides
additional protection from the risk of
electrical shock. When connecting the
GFCI to the electrical outlet, the
indicator should appear red. If the
indicator is not red, depress the RESET
button on the GFCI until the indicator
appears red.
Cleaning Tips
Wood Decks: Rinse deck and
surrounding area with fresh water. If
using detergent, fill the detergent
applicator bottle and apply to the area
being cleaned. For optimal results,
reduce your work area to small sections
and clean each section one at a time.
Allow the detergent to rest on the surface
for a few minutes and then rinse at high
pressure. Do not let the detergent dry on
the deck. Always clean from left to right
and top to bottom for best results. Rinse
at high pressure using the fan jet keeping
the tip of the spray nozzle 8-12 inches
from the surface.
Caution: For soft
woods, increase the distance from the
cleaning surface.
Cars, Boats, & Motorcycles:
Wet down
area to be cleaned before applying
detergent with clean water. Fill the
detergent applicator bottle and apply to
the area being cleaned. To achieve best
results, clean one side at a time. Allow
the detergent to rest on the surface for a
few minutes but do not let it dry. Rinse at
high pressure using the fan jet in a
sweeping motion keeping the tip of the
spray nozzle at least 8-10 inches away
from the surface. Maintain a further
distance when using a direct spray. Wipe
surface for a polished finish.
Storing Your Pressure Washer
When you have finished using your
pressure washer, follow these steps for safe
storage:
1. Turn the pressure washer to the "Off"
position.
2. Turn off the water supply.
3. Before disconnecting the high pressure
hose connection, point the trigger gun in
a safe direction away from you and
discharge the high pressure water.
Disconnect the high pressure hose from
the pressure washer and trigger gun.
4. Disconnect garden hose from pressure
washer.
5. Remove excess water from the pump by
tipping the unit on both sides to drain
any remaining water from the water
intake and outlet fittings.
6. Drain detergent tank and flush with clean
water.
7. Wipe away any remaining water on all
parts and fittings.
8. Engage the trigger gun safety lock.
9. Store the unit and accessories in a room
above 32°F.
8