Filter
Top Products
14
2.10 DIMENSIONS
2.10.1 Overall Width:
without deck deflector up deflector down
w/52” Deck 49.8 in. (126.5 cm) 53.4 in. (135.6 cm) 64.2 in. (163.1 cm)
w/60” Deck 53.8 in. (136.7 cm) 61.4 in. (156.0 cm) 72.2 in. (183.4 cm)
w/72” Deck 57.3 in. (145.5 cm) 73.4 in. (186.4 cm) 84.3 in. (214.1 cm)
2.10.2 Overall Length:
w/52” Deck w/60” Deck w/72” Deck
Roll Bar - Up 78.2 in. (198.7 cm) 78.2 in. (198.7 cm) 82.9 in. (210.6 cm)
Roll Bar - Down 88.9 in. (225.8 cm) 88.9 in. (225.8 cm) 93.6 in (237.7 cm)
2.10.3 Overall Height:
Roll Bar - Up Roll Bar - Down
71.4 in. (181.4 cm) 53.3 in. (135.4 cm)
2.10.4 Tread Width: (center to center of tires, widthwise)
w/52” Deck w/60” Deck w/72” Deck
Drive wheels 39.7 in. (100.1 cm) 43.7 in. (111.0 cm) 45.9 in. (116.6 cm)
Caster wheels 37.0 in. (93.9 cm) 39.0 in. (99.1 cm) 47.6 in. (120.9 cm)
2.10.5 Wheel Base: (center of caster tire to center of drive tire)
w/52” & 60” Decks w/72” Deck
50.3 in. (127.8 cm) 54.5 in. (138.4 cm)
2.10.6 Curb Weight:
w/52” Deck w/60” Deck w/72” Deck
1085 lbs. (492 kg) 1126 lbs. (511 kg) 1213 lbs. (550 kg)
2.11 TORQUE REQUIREMENTS
Bolt Location
Torque
Cutter Housing Spindle Nut ..................................... 140-145 ft-lbs. (190-197 N-m)
Blade Mounting Bolt (lubricate with anti-seize)...................55-60 ft-lbs. (75-81 N-m)
Engine Deck/Front Frame Mount Bolts ..............................30-35 ft-lbs. (41-47 N-m)
Anti-Scalp Roller Nuts........................................................40-45 ft-lbs. (54-61 N-m)
Engine Mounting Bolts ......................................................30-35 ft-lbs. (41-47 N-m)
Wheel Lug Nuts.............................................................90-95 ft-lbs. (122-129 N-m)
Wheel Motor Mounting Bolts............................................72-77 ft-lbs. (98-104 N-m)
Wheel Hub Slotted Nut ..............................................minimum125 ft-lbs. (169 N-m)
Rollover Protection System (Roll Bar) Mounting Bolts .......30-35 ft-lbs. (41-47 N-m)
Deck Drive Jackshaft Nut ..............................................75-80 ft-lbs. (102-108 N-m)
Clutch Retaining Bolt (secured with threadlocker)..............55-60 ft-lbs. (75-81 N-m)
3. OPERATION INSTRUCTIONS
3.1 CONTROLS
3.1.1 Familiarize yourself with all controls before operating the mower.
3.1.2 Motion Control Levers
: Located on each side of the console. The left lever
controls the flow of hydraulic oil from the left hydrostatic pump to the left drive
wheel motor. The right lever controls the flow of hydraulic oil from the right
hydrostatic pump to the right drive wheel motor.
IMPORTANT: To begin movement (forward or backward) the operator must
be in the seat, the brake lever must be disengaged (pushed down) before the
motion control levers can be moved in or the engine will kill.
When levers are centered in the T-slot the drive system is in the neutral position.
With levers moved out in the T-slot the drive system is in the neutral lock position
(See Figure 2).