Filter
Top Products
Operator's Manual
5-Ton Electric Log Splitter W1200
Check for parts online at www.getearthquake.com or call 800-345-6007 M-F 8-5
6
oil drain plug
dipstick
bleed screw
Figure 2
PARTS TO BE FREE OF
BURRS AND SHARP EDGES
THIS DRAWING AND ALL INFORMATION CONTAINED HEREIN IS AND REMAINS THE PROPERTY OF ARDISAM INC.
AND IS CONFIDENTIAL. IT IS SUBMITTED AND MAY BE USED ONLY IN CONNECTION WITH ARDISAMS' PROPOSALS
AND/OR ITS CUSTOMERS' ORDERS. IT SHALL NOT BE DISCLOSED TO OTHERS OR COPIED
WITHOUT ARDISAMS'
SPECIFIC WRITTEN CONSENT AND SHALL BE IMMEDIATELY RETURNED UPON REQUEST.
MATERIAL
TOLERANCE UNLESS
OTHERWISE NOTED:
0.0 ±.100 INCH ± 2.54 MM
0.00 ±.030 INCH ± 0.76 MM
0.000 ±.010 INCH ± 0.25 MM
ANGLES:
0 ± 2°
0.0 ± 1.0°
THREADS CLASS 2
PRIMARY DIMENSIONS ARE IN INCHES
SECONDARY DIMEMSION ARE IN MM
ALL ANGLES ARE DECIMAL DEGREES
UNLESS OTHERWISE SPECIFIED
NAME
TREATMENT
DR BY APPD PRT NO
W1200
PT WEIGHT
SURFACE AREA
DATE
REVISION
THIRD ANGLE PROJECTION
SEE BILL OF MATERIALS
NONE
32121.68
3451644.89
W1200 5 TON ELECTRIC
LOG SPLITTER
1
MATT OLSEN
MDO 9/17/2010
09/17/2010
SHEET: 6 OF 8
SET-UP AND PRE-OPERATION
Before attempting to use, familiarize yourself with all the
operating features and safety requirements of your log splitter.
(SEE FIGURE 1)
1. Wedge 8. 2-hand operating
2. Oil tank hydraulic control lever
3. Carrying handle 9. Safety guard for 2-hand
4. Supporting leg operating hydraulic
5. Motor w/push switch control lever
& circuit breaker 10. Log pusher
6. Rubber feet 11. Log cradle
7. Rolling wheel
WARNING
FOR YOUR OWN SAFETY, DO NOT CONNECT THE LOG
SPLITTER TO THE POWER SOURCE UNTIL THE MACHINE
IS COMPLETELY ASSEMBLED AND YOU READ AND
UNDERSTAND THE ENTIRE INSTRUCTION MANUAL.
FOR YOUR OWN SAFETY, NEVER FORGET TO BOLT THE
WHEEL BRACKET TO THE LOG SPLITTER, LIFT THE LOG
SPLITTER BY THE HANDLES AT BOTH ENDS AND PLACE
IT ON A 6075CM HIGH, STABLE, FLAT AND LEVEL WORK
SURFACE.
NEVER USE THE LOG SPLITTER IF IT IS NOT IN PERFECT
ORDER OR IF IT NEEDS SERVICING. BEFORE STARTING
WORK, CHECK CORRECT FUNCTIONING OF ALL THE
CONTROLS HYDRAULIC LEVER, PUSH BUTTON.
IMPORTANT
BEFORE OPERATING THE LOG SPLITTER, THE BLEED
SCREW SHOULD BE LOOSENED BY 34 ROTATIONS SO
AIR CAN GO IN AND OUT OF THE OIL TANK SMOOTH
LY. AIR FLOW THRU THE BLEED SCREW HOLE SHOULD
BE DETECTABLE DURING LOG SPLITTER OPERATION.
BEFORE MOVING THE LOG SPLITTER, MAKE SURE
THE BLEED SCREW IS TIGHTENED TO AVOID OIL
LEAKAGE FROM THIS POINT. See Figure 2)
CAUTION
FAILURE TO LOOSEN THE BLEED SCREW WILL RESULT IN
AIR BEING COMPRESSED AND DECOMPRESSED IN THE
HYDRAULIC SYSTEM. CONTINUOUS AIR COMPRESSION
AND DECOMPRESSION WILL BLOW OUT THE SEALS OF
THE HYDRAULIC SYSTEM AND CAUSE PERMANENT
DAMAGE TO THE LOG SPLITTER.
CAUTION
DO NOT ADJUST THE MAXIMUM PRESSURE LIMITING
SCREW. THE PRESSURE LIMITING SCREW HAS BEEN
SEALED AT THE FACTORY TO PREVENT UNAUTHORIZED
ADJUSTING. RESETTING THE SCREW WILL CAUSE
THE HYDRAULIC PUMP TO FAIL TO OUTPUT ENOUGH
SPLITTING PRESSURE OR CAUSE TOO MUCH PRESSURE,
WHICH MAY RESULT IN SERIOUS INJURY, AS WELL AS
DAMAGE TO THE MACHINE.
1
3
2
4
7
5
6
10
9
11
8
Figure 1