Filter
Top Products
Page 24
ROLLER PUMP PARTS BREAKDOWN
NOTE: Mount the Tee Valve (#19) to the Horizontal Valve
Mounting Bracket (#9; on page 21) using two 3/8" x 1-
1/4" hex head bolts (#29) and nylon locknuts (#30).
REF. PART
NO. NO. QTY. DESCRIPTION
ROLLER PUMP PLUMBING PARTS LIST
Vertical Panel
Mount
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
17
18
3
3
4
4
4
4
5
5
5
16
16
16
17
17
17
17
19
20
21
22
23
24
25
26
27
28
30
31
32
33
34
35
36
37
38
21
23
23
24
24
24
25
25
25
25
25
25
27
12
37
38
39
39
39
39
40
40
41
41
Optional Handgun
Plumbing
Handgun Plumbing
Installed Here
42
43
43
44
45
45
46
47
48
49
A
B
C
4
56
55
54
53
54
52
50
51
1. BEL114 1 1 1-1/4" MPT x 1" Hose Barb Elbow
2. CP114 PAV 1 1-1/4" Anti-Vortex Outlet Fitting
3. 1010RB - 1" I.D. Rubber Hose
4. B20H 6 1" Hose Clamp
5. BA3410 4 3/4"MPT x 1" H. Barb Fitting (GFP)
RVF34 40 1 3/4" Line Strainer
6. RVF34C 1 Strainer Cap
7. RVF340 1 40 mesh Screen
8. RVF34GV 1 Viton O-ring
9. RVF34B 1 Strainer Bowl
10. BM3400 1 3/4" Close Nipple (GFP)
11. BTT34 1 3/4" FPT Tee (GFP)
12. UV075FP 2 3/4" Ball Valve
13. BEL1010 1 1" MPT x 1" H. Barb Elbow (GFP)
14. C1700D 1 Roller Pump w/coupler
15. BEL1034 1 1" MPT x 3/4" H. Barb Elbow (GFP)
16. 340RB - 3/4" I.D. Rubber Hose
17. B12H 10 3/4" Hose Clamp
18. BEL3434 1 3/4" MPT X 3/4" H. B. Elbow (GFP)
19. AA17I 1 Three Section Tee Valve
20. 8460 1 3/4" Pressure Relief Valve
21. BA3434 2 3/4" MPT x 3/4" H. B. Fitting (GFP)
22. BA1234 3 1/2" MPT x 3/4" H. B. Fitting (GFP)
23. BA3412 3 3/4" MPT x 1/2" H. B. Fitting (GFP)
24. 120RB - 1/2" I.D. Rubber Hose
25. B8H 8 1/2" Hose Clamp
26. T12 1 1/2" Hose Barb Tee
27. BEL1212 2 1/2" MPT x 1/2" H. B. Fitting (GFP)
28. 100 GB 1 100 # Brass Pressure Gauge
29. 00523 2 3/8"-16 UNC x 1-1/4" Hex Hd. Bolt
30. 02592 8 3/8"-16 UNC Nylon Insert Locknut
31. 02800-10 1 Strainer Holder
32. 00263 1 3/8"-16 UNC x 1-1/2" Rd. U-bolt
33. 00851 1 5/16-18 UNC x 1-3/4" Rd. U-bolt
34. 02802 5 5/16"-16 UNC Nylon Insert Locknut
35. 5078V 1 Viton Grommet
36. N8P 1 Tank Outlet Nut
37. PO12D 2 1/2" Double Thread Outlet
38. R1212 2 1/2" MPT Tee
39. 5044 1 4 Single Agitation Wand
40. 5077V 1 Viton Grommet
41. N5P 1 Nut for Tank Outlets
50. 00036 2 5/16” Lock Washer
51. 01263 2 5/16” x 3/4” Grd. 5 Hex Bolt
52. 04298-30 1 Roller Pump Mounting Plate
53. 02772 1 1/4” Nylon Insert Lock Nut
54. 00214 2 1/4” Flat Washer
55. 04055 1 1/4” x 1” Grd. 5 Hex Bolt
56. 04299 1 Roller Pump Chain w/ hook
OPERATING INSTRUCTIONS
Begin operation by filling tank with liquid. Next, open the ball valve (A)
and the ball valve (B) in the agitation line. Open the AA171 Tee valve
(#19) and the by-pass valve (C). Start the pump. To regulate pressure,
slowly close valve (C) until the desire pressure is attained. If adequate
spraying pressure cannot be reached, slowly close the agitation valve (B)
until the desire spraying pressure is reached.
NOTE: Roller pumps will wear after normal use and a drop in pressure
can be expected. Simply reset the by-pass valve (C) to get the pressure
back to normal.
NOTE: Each jet agitator in the tank requires a minimum of 3 GPM.
Some roller pumps are limited in their capacity to spray and agitate at
the same time.
Please order replacement parts by PART NO. and DESCRIPTION.
OPTIONAL HANDGUN PARTS LIST
REF. PART
NO. NO. QTY. DESCRIPTION
42. UV075FP 1 3/4" Poly Ball Valve
43. BM3400 2 3/4" MPT Nipple
44. BTT100 1 1" FPT Tee (GFP)
45. B8H 2 1/2" Gear Clamp
46. BEL3412 1 3/4" MPT x 1/2" Hose Barb Elbow
47. D3412 1 3/4" MGHT x 1/2" Hose Barb
48. 2AAL60 1 15" Hand Spray Gun
49. 120RB - 1/2" Rubber Hose