Filter
Top Products
6. Correctly installed line will be the same length on both
sides.
NOTE: Do not rest the Hassle-Free III™ Cutting Head on the
ground while the unit is running.
Some line breakage will occur from:
• Entanglement with foreign matter
• Normal line fatigue
• Attempting to cut thick, stalky weeds
• Forcing the line into objects such as walls or fence posts
TIPS FOR BEST TRIMMING RESULTS
• For best trimming results, operate unit at full throttle.
• Keep the cutting attachment parallel to the ground.
• Do not force the cutting attachment. Allow the tip of the line
to do the cutting, especially along walls. Cutting with more
than the tip will reduce cutting efficiency and may overload
the engine.
• Cut grass over 8 inches (200 mm) by working from top to
bottom in small increments to avoid premature line wear or
engine drag.
• Cutting from right to left improves the unit's cutting
efficiency. Clippings are thrown away from the operator.
• Slowly move the trimmer into and out of the cutting area at
the desired height. Move either in a forward-backward or
side-to-side motion. Cutting shorter lengths produces the
best results.
• Trim only when grass and weeds are dry.
• The life of your cutting line is dependent upon proper
adherence of explained trimming techniques, what
vegetation is cut, and where vegetation is cut.
For example, the line will wear faster when trimming against a
foundation wall as opposed to
trimming around a tree.
DECORATIVE TRIMMING
Decorative trimming is
accomplished by removing all
vegetation around trees, posts,
fences and more.
Rotate the whole unit so that the
cutting attachment is at a 30°
angle to the ground (Fig. 14).
USING THE TWIST AND EDGE™ FEATURE
You can convert this unit to edge grass.
1. Make sure the unit is turned
completely off.
2. Turn the knob counterclockwise
to loosen coupler (Fig. 15).
3. Push in the release button (Fig.
16) and twist the shaft 90° until
the release button snaps into the
90° hole (Fig. 15).
4. Turn the knob clockwise to lock
the coupler (Fig. 17).
8
Fig. 14
OPERATING INSTRUCTIONS
HOLDING THE TRIMMER
Before operating the unit, stand in the operating position (Fig.
10). Check for the following:
• The operator is wearing eye protection and proper clothing
• With a slightly-bent right arm, the operator’s right hand is
holding the shaft grip
• The operator’s left arm is straight, the left hand holding the
assist handle
• The unit is at waist level
• The cutting attachment is parallel to the ground and easily
contacts the grass without the need to bend over
LINE REPLACEMENT
for Hassle-Free III™ Cutting Head
Always use Craftsman Hassle-Free
III™ XTRA QUIET Spiral Line.
Choose the line size best suited for
the job at hand. Red colored line is
designed for cutting grass and small
weeds. Black colored line is
designed for cutting larger weeds
and light brush.
NOTE: Before inserting new line into
the holes in the cutting head,
identify the proper holes.
Follow directions as shown
on the line glide plate. Do
Not attempt to remove the
cutting head from the unit
when replacing line.
1. Remove the old line and line glide plate from the cutting
head.
2. Clean entire surface of cut-
ting head. Note positions “A”
and “B” on the cutting head.
3. Reinstall line glide plate (Fig.
11). Align arrow with:
“A” when using medium (red)
or large (black) line, or
“B” when using lines with
diameters smaller than
medium (red) line
NOTE: Line glide plate must
be reinstalled in
cutting head before
inserting new line.
4. Insert both ends of your
line through the proper
holes in the side of the
cutting head (Fig. 12).
5. Pull the line and make
sure the line is against the
hub and is fully extended
through the positioning
tunnels (Fig. 13).
WARNING: Before you begin using any
attachment, read and understand the manual that
came with the attachment. Follow all safety
information contained within.
WARNING: To avoid serious personal injury and
damage to the unit, shut the unit off before
removing or installing add-ons.
WARNING: Always wear eye, hearing, foot and
body protection to reduce the risk of injury when
operating this unit.
Fig. 10
WARNING: Do not remove or alter the line cutting
blade assembly. Excessive line length will make the
clutch overheat. This may lead to serious personal
injury or damage to the unit.
Cutting
Head
Line Glide
Plate
Arrow
Fig. 11
Positioning
Tunnel
Fig. 12
Positioning
Tunnel
Line against
the hub
Fig. 13
Knob
Coupler
Fig. 15
90˚ Edging Hole
(Trimmer Only)