Filter
Top Products
28 Sp
Lavadoras a Presión
Sírvase darnos la siguiente información:
- Número del modelo
- Número de série (de haberlo)
- Descripción y número del repuesto según la lista de repuestos
Puede escribirnos a:
Campbell Hausfeld
Attn: Customer Service
100 Production Drive
Harrison, OH 45030
Para ordenar repuestos, sírvase lla-
mar al 1-800-330-0712 (En los
Estados Unidos, o llame a su dis-
tribuidor local)
No. Número
de Descripción del Ctd.
Ref. repuesto
1 Tubo del mango PM343715AV 1
2 * Perno de 6,4 mm (1/4") - 20 (mango) PM001903AV 2
3 * Arandela plana PM002000AV 14
4 * Tuerca de seguridad de nilon de
6,4 mm (1/4") - 20 ST073808AV 7
5 * Perno de 6,4 mm (1/4") - 20 (base) PM001902AV 3
6 Pata izquierda PM344828BH 1
7 Pata derecha PM345100BH 1
8 Defensa de caucho AL062300AV 2
9 * Tornillo autorrosc. 0,64 cm (1/4")
- 20 x 19,1 mm (3/4") MJ102100AV 2
10 Rueda WA120100AV 2
11 Tuerca de presión AL066300AV 2
12 * Perno de 6,4 mm (1/4") - 20 (Eje) PM001904AV 2
13 Eje PM344831BH 1
14 Placa de base GN004530AV 1
15 Tubo del detergente (not shown) PM013800AV 1
16 Pistola PM243000AV 1
17 Anillo en O (pistola) PM245800SV 1
18 Manguera PM344301AV 1
19 Lanza turbo (optional) PM243500AV 1
20 Lanza alta presión PM268500AV 1
21 Tanque de detergente PM268680AJ 1
22 Replacement Pump PM341000SJ 1
* Artículo disponible en ferreterías locales.
Hidrolavadora de Eje Vertical
1
2
3
4
14
7
8
9
10
11
5
6
13
12
18
16
19
17
20
21
Figure 8 - Trigger locked Figure 9 - Trigger unlocked
Engaged
Disengaged
5
Pre-Operation (Continued)
www.chpower.com
Figure 7– Attach lance to gun
7. Attach the lance with nozzle to the gun
(see Figure 7).
TRIGGER SAFETY LATCH
In the engaged position, the trigger
safety latch prevents the gun from being
triggered accidentally. Push the latch fully
down to engage it (See Figure 8 and 9).
Always engage the trigger safety latch
when the unit is not in use.
Operation
moving the choke ring fully to the
right. Turn the ignition switch to
“ON”.
7. Start the engine. Unlock the
trigger safety latch on the gun (See
Figure 9). Grasp the starter rope
and brace one foot on the chassis.
Point the gun in a safe direction.
While squeezing the trigger on the
gun, pull the starter rope rapidly
and firmly (See Figure 10).
Continue holding the rope as it
returns. Repeat these steps until
the engine starts.
DO NOT refuel a hot
engine. Refueling a
hot engine could cause a fire. Use only
fresh, clean regular or unleaded
gasoline. Close the fuel shutoff valve
during refueling.
3. Attach a garden hose to the inlet side
of the pump and connect it to the
water supply. Use a hose with an
internal diameter (I.D.) of 5/8 inch (1.58
cm) and a length of 50 ft. (15 m) or less.
Some local
plumbing codes
require backflow prevention when
connecting to a fresh water supply.
Install a backflow preventer upstream
from the pump if necessary.
a. If inlet water pressure is over 100
psi, install a regulating water valve
at the garden hose connection.
b. Do not exceed 100˚ F (38˚ C) inlet
water temperature.
NOTE: The inlet water supply must have a
minimum flow rate of 5 gpm (19 lpm).
4. Turn the water supply ON.
Never run the unit
dry. Be sure the
water supply is completely turned on
before operating the unit.
5. Trigger the gun until water sprays
smoothly from the tip indicating
that all air is purged from the
system. Lock the trigger safety latch.
6. Open the fuel valve by turning the
knob counterclockwise until it stops.
Close the choke (if engine is cold) by
The following cleaning procedure will
help you organize your cleaning task
and ensures that you will achieve the
best results in the shortest amount of
time. Remember to use the spraying /
cleaning techniques mentioned in the
following section.
Before starting a pressure washer
cleaning job, prepare the surface you
intend to clean. Clear furniture from
the area and make sure that all
windows and doors are closed tightly.
Also, protect all plants and trees near
the cleaning area with a drop cloth. A
covering ensures that your plants won’t
be sprayed by the detergents.
ALWAYS use the following start up
procedure to ensure that the unit is
started safely and properly.
If water has frozen
in the pressure
washer, thaw the pressure washer in a
warm room before starting. DO NOT
pour hot water on or into the pump;
internal parts will be damaged.
1. Check engine oil levels. Add oil as
necessary.
2. Check fuel level. Add unleaded
gasoline (rated 86 octane or higher)
as required
Pressure Washers
Figure 10 - Start the engine
1. Surface Preparation
2. Start Up