Black & Decker PW1600 Pressure Washer User Manual


 
IMPORTANT: The outer brass ring on the
garden hose quick connector MUST be
pulled back fully as shown in Fig. 11b)
before pushing it over the pump quick
connector (B). Water will not flow through
to the pump if these 2 connectors are not
fully coupled.
Figure 12 - Connect other end of garden
hose to the cold water source and turn
water on full. This pressure washer is not
intended to pump hot water. Never connect
it to a hot water supply as it will significantly
reduce the life of the pump.
OPERATION
NOTE: Before cleaning any surface, an
inconspicuous area should be cleaned to
test spray pattern and distance for
maximum cleaning results. If painted
surfaces are peeling or chipping, use
extreme caution as pressure washer may
remove the loose paint from the surface.
This Pressure Washer is equipped with
automatic delivery flow cut-off:
When the trigger is released, the dynamic
pressure automatically stops the motor.
When the trigger is pressed, the internal
pressure drop automatically starts the
motor and the spray pressure is restored
with a very slight delay.
Figure 13 - Ensure the on/off switch (I) is in
the off position before plugging in the unit.
Depress the switch portion marked “O” to
ensure unit is off. Plug the Ground Fault
Circuit Interrupter (GFCI) (G) into a power
outlet. Indicator should turn red. T
EST
BEFORE EACH USE. Press the “TEST”
button. Red indicator should disappear.
Press “RESET” button again for use. Do
not use if above test fails.
Figure 14 - Before each use, ensure the
gun safety catch is released by pushing it
down as shown, then press the trigger for a
few seconds to allow air to escape and to
discharge residual pressure in the hoses.
Figure 15 - Turn on the pressure washer by
depressing the bottom half of the switch (I)
marked “I”. The unit will run for a few
seconds as it builds up pressure, then will
shut off. It will run on demand as the gun
trigger is depressed. Turn off the pressure
washer by depressing the upper half of the
switch marked “0”.
YOUR PRESSURE WASHER IS NOW
READY TO USE - PLEASE REVIEW THE
FOLLOWING FOR DETAILS ON
ACCESSORIES APPLICATION.
SET-UP / ADJUSTMENT
Figure 7 - Insert the fan wand (D) into the
gun wand (F) by pushing and rotating until
the two parts are locked as shown in
Figure 7.
Figure 8 - Connect the high pressure hose
(F1) to the water (OUTLET) (A) on the unit
by first inserting the brass end of the hose
into the threaded outlet on the front of the
unit, then snugly threading on the hose
coupling.
Figure 9 - Connect the garden hose quick
connector (J) to your garden hose as shown
in Fig. 9. The intake water temperature
must NOT exceed 50°C (122°F). The water
supply pressure must be between
20 and 80 psi.
CAUTION: The pressure washer must
only be used with clean water; use of
unfiltered water or corrosive chemicals will
damage the pressure washer.
Figure 10 - With the quick connector (J)
attached to your garden hose, pull back on
its outer ring and push firmly onto the
mating pump quick connector (B), (already
attached to the pressure washer inlet), then
release ring to engage.
bumps of wheel as shown and press center
of wheel cap until it snaps securely to
wheel.
Handle Assembly - PW1750
Align and begin to push tubes of handle (K)
down inside lower tubes (N) as shown.
Press spring buttons (R) of handle (K)
inward as handle tubes are pushed down
fully into lower tubes (N), and both spring
buttons protrude out through holes in lower
tube (N) completing assembly.
Upper Cord Wrap Hook Assembly - PW1750
Insert cord wrap top hook (M) into the rear
slots in handle (K) by pushing upward and
inward to snap in place. Drive two 1/2” self
tapping screws included in cord hook bag
through cord wrap holes into handle as
shown until tight. DO NOT over tighten.
6
High pressure hose
7
O
I
6
7
8
9
10
12
15
13
14
11
a)
b)
Pump Quick
Connector
O
I
PW1750
R
4
PW1750
PW1750
5