American Standard 1730 SERIES Hot Tub User Manual


  Open as PDF
of 4
 
INSTALLATION INSTRUCTIONS
753451-100 Rev. A
© American Standard Inc. 2003
All product names listed herein are trademarks
of American Standard Inc. unless otherwise noted.
HIGH GLOSS ACRYLIC
SHOWN LESS ALL FITTINGS
COLONY™ CORNER
WHIRLPOOL/BATHING POOL
1730 SERIES
FOR AFTER-SALES SERVICE CALL 1 (800) 442-1902 WEEKDAYS.
THANK YOU...
for selecting an American Standard bath. Your new
bath is shipped to you after careful inspection. The
whirlpool version is completely assembled with pump,
motor, and system piping. All you need to finish the
installation are your selected fittings and electrical
connections for a whirlpool.
To insure maximum performance and pleasure from
this product, please follow the instructions and
cautions.
GENERAL INSTALLATION INFORMATION
Carefully uncrate and inspect your new bath for any shipping damage. If such damage is found, report it to your vendor
immediately. After inspection and during installation, protect the bath from construction damage. After installation, and before
enclosing with wallboard, tile, etc., water test the unit and check for leaks.
If a whirlpool, do not make modifications to the whirlpool system or remove pump from factory mounting. This could adversely affect
the safety and performance of the whirlpool and void the warranty. Do not handle or move the whirlpool by the pump, motor, or
piping system.
Fittings (bath filler, shower arm, etc.) are not provided with the bath and must be ordered separately. Framing and enclosing
materials are provided by others. Check for availability of optional American Standard wall tiling bead (required for recess
installations).
Protect all finished surfaces of the whirlpool during construction and installation using a drop cloth.
WARNING! Do not lift whirlpool by the piping harness at any time.
List of Optional Components (not included):
• Apron Kit*
* see your American Standard Distributor
List of Required Components (not included):
• Drain 1583.470*
• Bath Filler*
* see your American Standard Distributor
List of Required Tools and Supplies:
Tools
• Level
• Tape Measure
• Pipe Wrench
• Slip Joint Pliers
• Screw Driver
• Standard
Woodworking Tools
• Personal Safety
Equipment
• Caulking Gun
Supplies
• Nails
• Putty
• Caulking (waterproof)
• 1 x 3 or 2 x 2
Stringers
• Drop Cloth
• 15 amp GFCI
Outlet
• Cement, Plaster,
Grout
495mm
(19
-1/2)
117mm
(4
-5/8)
C/L OF DRAIN
OUTLET
51mm
(2)
1546mm
(60-7/8)
ALT.
PUMP
1064mm
(41-7/8)
686mm
(27)
318mm
(12-1/2)
1168mm
)(46
1514mm
(59-5/8)
TOP OF
DECK
445mm
(17-1/2)
70mm
(2-3/4)
ROUGH
FLOOR
83mm
(3-1/4)
BATH SUPPORT MATERIAL
38mm (1-1/2)
O.D. TAILPIECE
PUMP
PROVIDE ACCESS
FOR SERVICING
PUMP & CONTROLS
(6) JETS
ON/OFF
SWITCH
2 AIR
VALVES
LEVELING
STRINGER
NOT FOR
SUPPORT
483mm
(19)
2134mm
)(84
*
60 x 60 x 19-1/2 In.(1524 x 1524 x 495mm)
115 Lbs. (52 Kg.)
908 Lbs. (412 Kg.)
95 Gal. (360 L.)
65 Gal. (246 L.)
30 x 50 In. (762 x 1270mm)
45-1/2 x 63-1/2 In.(1156 x 1613mm)
13 In. (330 mm)
36 Lbs./Sq. Ft. (177 Kgs/Sq. m.)
27.8
54
GENERAL SPECIFICATIONS FOR 1730 WHIRLPOOL
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
WHIRLPOOL MIN. OPERATING VOL.
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
PTS.
CUBE (FT
3
)
WHIRLPOOL ELECTRICAL SPECIFICATIONS
1.1 HP, 9.9 AMPS, 120V.SYSTEM I PUMP
* NOTE: If the optional apron (PN 0730.121) is to be used with this
tub, the stringer height must be referenced from the finished floor.
next