Grizzly G0555P Manual

A SERVICE OF

next previous

BdYZa<%***$<%***EB[\#H^cXZ*$&&

"'*"

5. Add` Vi l]Vi i]Z iZch^dc \Vj\Z gZVYh VcY

jhZi]ViVhV\j^YZ[dgiZch^dc^c\i]ViWaVYZ

^ci]Z[jijgZ#

 Note: Do not rely on this setting for long

periods of time because the blade will stretch

with use.

Additionally, with extended use, the blade

tensioning system may need to be reset for

correct operation. Refer to the Resetting

Blade Tensioner in the Service section on

this manual.

Adjusting Blade

Support Bearings

I]Z hjeedgi WZVg^c\h VgZ edh^i^dcZY WZ]^cY i]Z

WaVYZidegZkZci^i[gdbYZ[aZXi^c\WVX`lVgYYjg"

^c\ Xjii^c\ deZgVi^dch# EgdeZg VY_jhibZci d[ i]Z

hjeedgi WZVg^c\h ^hVc ^bedgiVcieVgi d[bV`^c\

VXXjgViZ Xjih VcY `ZZeh i]Z WaVYZ iZZi] [gdb

Xdb^c\ ^c XdciVXi l^i] i]Z WaVYZ \j^YZh l]^aZ

Xjii^c\#

I]ZgZ VgZ hjeedgi WZVg^c\h dc i]Z jeeZg VcY

adlZgWaVYZ\j^YZVhhZbWa^Zh#7di]VY_jhi^ci]Z

hVbZbVccZg#

Whenever changing a blade or adjusting

tension and tracking, the upper and lower

support bearings and blade guides must be

re-adjusted before cutting operations.

Tool Needed Qty

LgZcX]&%bb####################################################&

To adjust the support bearings:

1. BV`ZhjgZi]ZWaVYZ^higVX`^c\egdeZganVcY

^hXdggZXianiZch^dcZY#

2. 9>H8DCC:8I76C9H6L;GDBEDL:G

3. ;Vb^a^Vg^oZndjghZa[l^i]i]ZhjeedgiWZVg^c\

Xdcigdahh]dlc^ci]Z[^\jgZWZadl#

@cjgaZY

@cdW

6hhZbWanAdX`7dai

Hjeedgi

7ZVg^c\

Figure 29.HjeedgiWZVg^c\Xdcigdah#

I]jbWhXgZl

4. AddhZci]Z\j^YZVhhZbWanadX`Wdaihdi]Vi

i]Z hjeedgi WZVg^c\ XVc WZ gdiViZY eZgeZc"

Y^XjaVgidi]ZWaVYZ^ci]ZcZmihiZe#

5. GdiViZ i]Z WaVYZ \j^YZ VhhZbWan jci^a i]Z

[VXZ d[ i]Z hjeedgi WZVg^c\ ^h eZgeZcY^Xj"

aVg id i]Z WaVYZ! Vh ^aajhigViZY ^c i]Z [^\jgZ

WZadl#

7VcYhVl

7aVYZ

Hjeedgi

7ZVg^c\

Figure 30.I]Z[VXZd[i]ZhjeedgiWZVg^c\bjhi

WZeZgeZcY^XjaVg.%idi]ZWaVYZ#

When using a

3

⁄4" blade, the blade tensioning

system may need to be reset for correct

operation. Refer to Blade Tensioner on Page

53 for detailed instructions.