TP Receivers • Installation and Operation
TP Receivers • Installation and Operation
Installation and Operation, cont’d
2-8
TP R 15HD A only — For optional rack mounting, mount the
receiver on a VersaTools 19" 1U Rack Shelf (Extron part
#60-190-20) (figure 2-4). The TP R 15HD A mounts in one of
four locations on the rack.
(2) 4-40 x 3/16" screws
Use 2 Mounting Holes on
Opposite Corners
VersaTools Rack Shelf
1/4 Rack Width False Front
Face Plate
T
P
R
1
5
H
D
A
R
G
B
P
E
A
K
IN
G
L
E
V
E
L
T
P
R
1
5
H
D
A
R
G
B
PE
A
K
IN
G
LE
VE
L
T
P
R
1
5
H
D
A
R
G
B
P
E
A
K
IN
G
L
E
V
E
L
Figure 2-4 — VersaTools rack mounting the TP R 15HD A
1. If feet were previously installed on the bottom of the
receiver, remove them.
2. Mount the receiver on the rack shelf, using two 4-40 x 3/16
screws in opposite (diagonal) corners to secure the receiver
to the shelf.
3. Install blank panel(s) (included in the 1U universal and
VersaTools rack kits, optional for the 1U basic rack kit) or
other unit(s) to the rack shelf.
Only the TP R 15HD A and products in the Extron
VersaTools line can be mounted on a VersaTools shelf.
Any 1U rack-mountable Extron product can be mounted
on the standard shelf.
Furniture mounting
All of the receiver models can be mounted under furniture such
as a table or podium surface using the appropriate optional
mounting bracket, Extron’s Mini Under-Desk Mounting Kit
(part #70-212-01) (TP R 15 HD A) or Under-Desk Mounting Kit
(part #70-077-01) (all other models).
All models except the TP R 15HD A can be mounted through a
table or podium using Extron’s Through-Desk Mounting Kit
(part #70-077-02). Furniture mount the receiver as follows:
1. Attach the mounting brackets to the receiver with the
machine screws provided (figure 2-5).
Extron
TP R BNC A
Extron
TP R BNC A
Extron
TP R 15HDA
RGB INPUT
RGB OUTPUT
R
G
B
H/HV
V
A
AUDIO
L
R
B
SOG
C SYNC
P
O
W
E
R
15V
.
5
A D
C
L
R
R
G
B
I
N
P
U
T
R
G
B
O
U
T
P
U
T
R
G
B
H
/
H
V
V
A
A
U
D
I
O
L
R
B
S
O
G
C
S
Y
N
C
P
O
W
E
R
1
5V
.5
A
D
C
LR
Through-desk
Mounted
Under-desk
Mounted
Under-desk
Mounted
TP R 15HD A
R
G
B
P
E
A
K
IN
G
L
E
V
E
L
Figure 2-5 — Under-desk or through-desk mounting
2. For through-surface mounting (all except TP R 15HD A),
cut the proper sized hole in the mounting surface.
3. Hold the receiver with the attached brackets against the
underside of the table or other furniture. Mark the
location of the screw holes of the bracket on the mounting
surface.
4. Drill 3/32” (2 mm) diameter pilot holes, 1/4” (6.3 mm)
deep in the mounting surface at the marked screw
locations.
2-9
