NAME OF EACH PART OF PROJECTOR
FRONTOFCABINET "'1:1:1-1:4::1:1.." .
~
~
.., "", '... ~
h. .Op"",,"c.,m / ~-
ill CAUTION ~ - --- .
D? not tu,n on the p,oj..to, < ,..
withthelenscapattached.High:~~ I :-
::perature from light b..m\
.
~~'II'
.
..,-.-
I
t
...
.
.
y ~8m8ge the lens cap .nd;~~
\
/ ~. .
resu" onfo,. hezerd. ."h~. ~'. . i i;~~HH. i111,
G
. '~/ -
~.
'~~~~~iii
.
'i
.
'
.
P
~
!;/
11I1I
11
"'"'''''' .,
A "if':;;;:e"
_.:I~J.."'''''~
*Option8l:LC-X71l ~~
BACK OF CABINET
N
.2:t:""h'.''':I~I.
&. HOTAIR EXHAUSTEDI
Air blown from the exhaust vent is hot.
When using or Installing the projector.
the following precautions should be
taken.
. Do not put a flammable object near this
vent
. Keepthereargrillsat least 3.3' (1m)
away from any object, especially from
heat-sensitiveobjects.
. Donottouch this area, especially
screws andmetallic parts. Thisareawill
become hot when the projector is in
use
This projector detects internal
temperature and automatically controls
operating power of the cooling fans.
When attaching the Pj-to NetDirector
(optional) to the projector, remove these
parts. Refer to the owner's manual of the
optionalPJ-toNetDirector.
BOTTOM OF CABINET
_.11:.ll' 1~4::a'..~I.'1.~...
This projector is equipped with the cooling fans for protecting
from overheating. Pay attention to the followings to ensure
proper ventilation and avoid a possible risk of fire and malfunction.
. Do not cover the vent slots
. Keep this side dear of any objects. Obstructions may block
coolingair
..
..'
. .
. '
POSITIONING PROJECTOR
NOTE: The figures below are only for the Model LC-X71.
The projection lens isnot provided with the Model LC-X71 L
. This projector isdesigned to project on a flat projection surface.
. Pro,ectorcan be focused from 4.6' (1.4 m) - 48.2' (14.7 mI.
. Refer to the figure below to adjust the screen size
A ROOM UGHT
Brightness in a room has a great
influence on the picture quality. It is
recommended to limit ambient lighting
in order to provide the best image.
Co)
LENS SHIFT ADJUSTMENT
Projection lens can be moved up and down with the motor-driven Lens shift function. This function makes it
easy to provide projected image where you want. The U/D ratio can be adjusted 10:0 - 1:1 (see the figure
below).
HiGhest (10 .0) .
~.
~~"u~:
lENS INSTALLATION
Before setting up the projector, install a projection lens on
the projector.
1. Before installation, check the area where the projector is
used and prepare a suitable lens. For the specifications of
a projection lens, contact sales dealer where you
purchased the projector.
2. For installation, refer to the installation manual of the
optional lens.
t/Note:
o\rV1leninstoJ/ingthelens. reffiOl'e(he(CNefWP o((he ptOJe<tor.
SETTING-UP PROJECTOR
CONNECTING AC POWER CORD
This projector uses nominal input voltages of 100-120 V or
200-240 V AC and it automatically selects correct input
voltage. It is designed to work with single-phase power
systems having a grounded neutral conductor. To reduce
risk of electrical shock, do not plug into any other type. of
power system.
If you are not sure of the type of power being supplied,
consult your authorized dealer or service station.
Connect the projector with all peripheral equipment before
turning it on.
~ CAUTION
For safety, unplug the AC power cord when the projector
is not in use. When the projector isconnected to an outlet
with the AC power cord, it is in stand-by mode and
consumes a little electric power.
ADJUSTABLE FEET
Projection angle can be adjusted up to 10.5 degrees with the
ADJUSTABLE FEET.
1
2 Release the FEET LOCK LATCHES to lock the
ADJUSTABLE FEET and rotate the ADJUSTABLE FEET
to a proper hight, and tilt.
Uft the front of the projector and pull the FEET LOCK
.ATCHES in each side of the projector.
3 To retract the ADJUSTABLE FEET, lift the front of the
projector and pun and undo the FEET LOCK LATCHES.
\
INSTALLING PROJECTOR IN PROPER POSITION
Install the projector properly. Improper installation may reduce the lamp life and cause a fire hazard.
10'
00 not tilt the projector more than 10 degrees from side to side.
NO SIDEWAYS
Do not put the projector on either side to project an image
NOTE ON POWER CORD
AC power cord must meet the requirements of the country where you use the
projector.
Confirm the ACplug type with the chart below and a proper AC power cord must
beused.
If the supplied AC power cord does not match your ACoutlet, contact your sates
dealer.
I
Projector side
AC Outlet side
If:
Forthe U.S.A.andCanada For Continental Europe
Ground
I..
..r..
..r..
ToPOWERCORD
I
CONNECTORonyour
To the AC Outlet
Tothe AC Outlet
projector.
1120 V AC)
(200 -240 VAC)
