Filter
Top Products
17
.
Figure 24
• Secure with the bell washer and hex bolt removed
earlier.
• Secure the frame cover with six self-tapping
screws. Put the snow thrower down to its normal
operating position.
NOTE: If you placed plastic film under the gas cap, be
certain to remove it.
Engine
Refer to separate engine manual for all engine
maintenance procedures.
SECTION 8: OFF-SEASON STORAGE
• If unit is to be stored over 30 days, prepare engine
for storage as instructed in the engine manual.
• Remove all debris from the exterior of equipment.
• Follow lubrication recommendations on page 13.
• Always store the snow thrower in a clean, dry area.
NOTE: When storing any type of power equipment in
an unventilated or metal storage shed, care should be
taken to rust proof the equipment. Using a light oil or
silicone, coat the equipment, especially any chains,
springs, bearings and cables.
Safety & Decorative Labels: Part Number and Location
Shift Arm
Assembly
Pin
Friction
Wheel
Sprocket
Spacer
Sprocket
Hex Hub
of Sprocket
Hex
Shaft
Spacer
WARNING: Never store engine with fuel in
tank indoors or in poorly ventilated areas,
where fuel fumes may reach an open flame,
spark or pilot light as on a furnace, water
heater, clothes dryer or other gas appliance.
777I20747
777I20412
CU
T
OU
T
CHUTE
DIRECTIONAL CONTROL
CLOCKWISE TO
DISCHARGE LEFT
COUNTER CLOCKWISE
TO DISCHARGE RIGHT
LEFT TURN CONTROL
6
1
2
F
3
4
5
R2
R1
AUGER CONTROL
R
CUT OUT
CHUTE
TILT
CONTROL
RIGHT TURN
CONTROL
TRACTION CONTROL
•
IMPORTANT: THIS MACHINE IS EQUIPPED
WITH AN AUGER CONTROL LOCK.
TO STOP AUGER, BOTH AUGER CONTROL
AND TRACTION CONTROL LEVERS MUST
BE RELEASED.
TO STOP ENGINE, PULL OUT IGNITION KEY.
FOR STEERABLE OPERATION:
SQUEEZE LEFT TURN CONTROL TO STEER
SNOWTHROWER TO THE LEFT. SQUEEZE RIGHT
TURN CONTROL TO STEER SNOWTHROWER
TO THE RIGHT.
•
READ OPERATORS MANUAL BEFORE STARTING.
•
INSERT IGNITION KEY INTO SLOT.
MAKE SURE IT SNAPS INTO PLACE.
DO NOT TURN KEY.
•
RECOIL STARTER:
PUSH PRIMER 2 OR 3 TIMES.
ELECTRIC STARTER:
DO NOT PRIME.
•
PUSH START BUTTON OR PULL ROPE HANDLE
TO START ENGINE.
•
SELECT SPEED REQUIRED. SQUEEZE RIGHT
TRACTION CONTROL LEVER TO MOVE.
RELEASE TO STOP.
ALWAYS RELEASE TRACTION CONTROL
LEVER BEFORE CHANGING SPEEDS.
•
FOR SNOWTHROWING, ENGAGE LEFT AUGER
CONTROL LEVER BEFORE TRACTION
CONTROL LEVER.
Halogen Headlight Ha l og e n H e a dl i gh t • Remote Pitch Control R e mo t e P i t ch Co n t ro l
6016
Halogen Headlight • Remote Pitch Control
777D00133
777S32066
777S32065
DANGER
NEVER PUT HAND IN CHUTE. CONTACT WITH
ROTATING PARTS CAN AMPUTATE FINGERS
AND HANDS. USE CLEAN-OUT TOOL TO
UNCLOG DISCHARGE CHUTE.
DO NOT UNCLOG DISCHARGE CHUTE WHILE
ENGINE IS RUNNING.
SHUT OFF ENGINE AND REMAIN BEHIND
HANDLES UNTIL ALL MOVING PARTS HAVE
STOPPED BEFORE UNCLOGGING.
DANGER
AVOID INJURY FROM
ROTATING AUGER -
KEEP HANDS, FEET
AND CLOTHING AWAY.
KEEP AWAY FROM ROTATING IMPELLER
AND AUGER. CONTACT WITH IMPELLER OR
AUGER CAN AMPUTATE HANDS AND FEET
.
USE CLEAN-OUT TOOL TO UNCLOG
DISCHARGE CHUTE.
DISENGAGE CLUTCH LEVERS, STOP ENGINE,
AND REMAIN BEHIND HANDLES UNTIL ALL
MOVING PARTS HAVE STOPPED BEFORE
UNCLOGGING OR SERVICING MACHINE.
TO AVOID THROWN OBJECTS INJURIES,
NEVER DIRECT DISCHARGE AT BYSTANDERS.
USE EXTRA CAUTION WHEN OPERATING ON
GRAVEL SURFACES.
READ OPERATOR'S MANUAL.
1.
2.
3.
4.
5.
DANGER
CLEAN-OUT TOOL
3
777D00181
MODEL PLATE
1