Filter
Top Products
7 12
SAFETY INSTRUCTIONS (continued)
OPERATIONAL SAFETY
The use of this equipment is subject to certain hazards which cannot be protected against by mechanical
means or product design. All operators of this equipment must read and understand this entire manual, pay-
ing particular attention to safety and operating instructions, prior to using. If there is something in this manu-
al you do not understand, ask your supervisor, or your dealer, to explain it to you.
Be sure power unit is in good condition. Read all the safety precautions and make sure all operators are famil-
iar with the safety rules of operation.
Know your controls and how to stop the power unit and engine quickly in an emergency. READ THIS MANU-
AL AND THE ONE PROVIDED WITH YOUR TRACTOR AND LOADER, OR SKID STEER.
Most accidents occur because of neglect or carelessness. Keep all helpers and bystanders fifty feet (50’) from
an operating power unit and attached equipment. Only properly trained people should operate this machine.
It is recommended the tractor be equipped with a Rollover Protection System (ROPS) and a seat belt that is
used. Always stop the tractor, skid steer, or forklift, set brake, shut off the engine, remove the ignition key, and
lower loader and attachment to the ground before dismounting. Never leave equipment unattended with the
engine running.
Please remember it is important that you read and heed the safety signs on the front loader attachment and
loader, and the safety rules set forth. Clean or replace all safety signs if they cannot be clearly read and under-
stood. They are there for your safety as well as the safety of others. The safe use of this machine is strictly
up to you, the operator.
The use of any loader attachment is NOT recommended on tractor with a tricycle wheel arrangement. Tricycle
type tractors are unstable for front loader use.
A heavy load can cause instability in driving a power unit. Make sure the front or rear of the power unit is
properly counter-balanced with weights. Always drive slowly – especially around turns. An unstable power unit
could steer badly and possibly tip over, causing injury or death.
When the use of hand tools is required to perform any part of assembly, installation, adjustment, maintaining,
repairing, removal, or moving the implement, be sure the tools used are designed and recommended by the
tool manufacturer for that specific task.
Personal protection equipment including safety glasses, safety shoes, and gloves are recommended during
assembly, installation, operation, adjustment, maintaining, repairing, removal, or moving the attachment.
Always use two people to handle heavy, unwieldy components during assembly, installation, removal, or
moving the loader attachment.
Never place any part of your body where it would be in danger if movement should occur during assembly,
installation, operation, maintaining, repairing, removal, or moving the implement.
Do not allow others to ride on the power unit with an operator. Riders are subject to injury such as being struck
by foreign objects or being thrown off. Riders obstruct the operator’s view resulting in unsafe operation. Never
allow anyone to ride on the implement!
SAFETY INSTRUCTIONS (continued)
After servicing, be sure all tools, parts and service equipment are removed.
Check to ensure all safety signs are installed and in good condition. (See safety sign section for location
drawing.)
Do not allow grease or oil to build up on any deck or platform.
Never replace hex bolts with less than grade five bolts unless otherwise specified, i.e. shear bolts. Refer to bolt
torque chart for head identification marking.
Where replacement parts are necessary for periodic maintenance and servicing, genuine factory replacement
parts must be used to restore your equipment to original specifications.The manufacturer will not claim respon-
sibility for use of unapproved parts and/or accessories and other damages as a result of their use.
If equipment has been altered in any way from original design, the manufacturer does not accept any liability
for injury or warranty.
A fire extinguisher and first aid kit should be kept readily accessible while performing maintenance on this
equipment.
Following operation or when unhooking, stop the skid steer or tractor, set the brakes, shut off the engine,
relieve all hydraulic pressure and remove the ignition keys.
Store the unit in an area away from human activity.
Do not park equipment where it will be exposed to livestock for long periods of time. Damage and livestock
injury could result.
Do not permit children to play on or around the stored unit.
Make sure all parked machines are on a hard, level surface and engage all safety devices.
If blocking is used, make sure it is solid and secure before leaving area.
MAINTENANCE SAFETY (continued)
STORAGE SAFETY