Filter
Top Products
8
S
Cutonly grass, weeds, andwoody brushup
to 1/2 inch in diameter with the weed blade.
Do not let the blade contact material it can-
not cut such as stumps, rocks, fences,
metal, etc., orclusters ofhard, woody brush
having a diameter great er than 1/2 inch.
S
Keep the blade sharp. A dull blade is more
likely to snag and thrust.
S
Cut only at full throttle. The blade will have
maximum cutting power and is less likely to
bind or stall.
S
“Feed” the blade deliberately and not too
rapidly. The blade can thrust away if it is fed
too rapidly.
S
Cut only from your right to your left. Swing-
ing the unit in the s ame direction as the
blade spins increases the cutting action.
S
Use the shoulder strap and keep a firm grip
on the unit with both hands. A properly ad-
justed shoulder strap will support the
weight of the unit, fr eeing your arms and
hands to control and guide the cutting mo-
tion.
S
Keep feet comfortably spr ead apart and
braced for a possible sudden, rapid thrust of
unit. Do not overr each. Keep firm footing and
balance.
S
Keep blade below waist level; it will be eas-
ier to maintain c ontrol of unit.
S
Donot raise theengine above your waistas
the blade can come dangerously close to
your body.
S
Do not swing unit with such force that you
are in danger of losing your balance.
Bring the engine to cutting speed before en-
tering the material to be cut.
If the blade does not turn when you squeeze
the throttle trigger, make sure tube is fully in-
serted into the engine.
Always release the throttle trigger and allow
engine to return to idle speed when not cut-
ting. The blade should not turn while the en-
gine is running atidle. If the blade turns atidle,
do not use your unit. Refer to the Carburetor
adjustment section or contact your Autho-
rized Service Dealer.
S
Maintain good firm footing while using t he
unit. Do this by planting feet firmly in acom-
fortable apart position.
S
Cut w hile swinging the upper part of your
body from right to left.
S
As you move forw ar d to the next area to cut,
be sure to maintain your balance and footing.
Cut using the 8 o’clock
to 10 o’clock position of
the blade
10 o’clock
8 o’clock
WARNING:
The operator or others
must not try to clear away cut m aterial with the
engine runningorthe bladeturningto avoidseri-
ous injury. Stop engine andblade beforerem ov-
ing materials wr apped around blade or tube.
REPLACING THE LINE
S
Move the ON/OFF switch to the OFF posi-
tion and ensure trimmer head has fully
stopped.
S
Remove the spool by firmly pulling on the
tap button.
S
Clean entire surface of hub and spool.
S
Replace with a pre-wound spool, or cut two
lengths of 12-1/2 feet of 0.080” (2 mm) di-
ameter WeedEater
R
brand line. Never use
wire, rope, string, etc., which can break off
and become a dangerous missile.
S
Insert ends of line about 1/2 inch (1 cm) into
the small holes on the inside of the spool.
Small
Holes
Spool
Hub
Line in Notch
Line in Notch
Line exit holes
S
Wind the line evenly and tightly onto the
spool. Wind in t he direction of the arrows
found on the spool.
S
Push the lines into the notches, leaving 3to
5 inches (7 -- 12 cm) unwound.
S
Insert the lines into the the exit holes in the
hub as shown in the illustration.
S
Align notches with the line exit holes.
S
Push the spool into the hub until it snaps
into place.
S
Pull the lines extending outside ofthe hub to
release the lines from the notches.
SERVICE
We recommend all service and adjustments
not listed in this manual be performed by an
Authorized Service Dealer.
CARBURETOR ADJUSTMENT
Your carburetor i s equi pped wi th limiter caps.
Damage w ill occur if you turn the needles be-
yond the limitercaps. Adjustingthe carburetoris
a complicated task. We recommend that you
take your unit to an Authorized Serv ice Dealer.
SPARK PLUG
Replace spark plug yearly with a Champion
RCJ-8Y plug. Spark plug gap is 0.025 inches.
IGNITION TIMING
Ignition timing is fixed, non-adjustable.