Weed Eater 2500 Blower User Manual


 
4
BLOWER SAFETY
D
Use only in daylight or in good artificial
light.
D
Inspect the area before using the unit.
Remove all debris and hard objects such
as rocks, glass, wire, etc., that can rico-
chet, be thrown, or otherwise cause injury
or damage during operation.
D
A void accidental starting. Be sure the
sw itc h is in the
OFF
position and keep
your hand and fingers away from the
switch while connecting the unit to the
power source or when carrying a unit
connected to the power source.
D
Never run the unit without the proper
equipment attached. When used as a
blower , always install a blower tube. Use
only recomm ended attachments. D o not
use with any opening blocked, Keep free
from dust, lint, hair and anything that may
reduce air flow .
D
To avoid spreading fire, do not use blower
near leaf or brush fires, fireplaces, barbe-
cue pits, ashtrays, etc.
D
Never place objects inside the blower
tubes; always direct the blowing debris
away from people, animals, glass, and
solid objects such as trees, automobiles,
walls,etc.Theforceofaircancause
rocks, dirt, or sticks to be throw n or to r ico-
chet which can hurt people or animals,
break glass, or cause other damage.
D
Never use for spreading chem icals, fertil-
izers, or any other substances which may
contain toxic materials.
VACUUM SAFETY (If applicable)
WARNING:
Only use the Flex Vac
Kit FV1910 w ith model 2540 and 2560 onl y.
DO NOT
use with any other models.
D
Stop the motor and disconnect the power
source before opening the air inlet door or
attemptin g to inse rt or rem o v e the vac u-
um tubes. The motor must be s topped
and the impeller blades no longer turning
to avoid serious injury from the rotating
blades.
D
Hard objects can b e thrown through the
collection bag or the housing and be-
come dangerous missiles which can
cause serious injury to operator or others.
D
When using the vacuum attachment, the
unit is designed to pick up dry material
such as leaves, grass, sm all twigs, and
bits of paper . Do not vacuum stones,
gravel, metal, broken glass, etc., to avoid
severe dam age to the impeller . To avoid
the possib ility of electric a l shock , do not
attempt to vacuum water or other liquids.
D
Never run the unit without the proper
equipment attached. When used as a
vacuum, always install vacuum tubes
and collection bag assembly. Make sure
the colle c tion b ag asse mb ly iscom plete ly
zipped when unit is running to avoid flying
debris. Use only recommended attach-
ments.
D
A void s ituations which could set the col-
lection bag on fire. Do not vacuum dis-
carded matches, cigars, cigarettes, or
ash from fireplaces, barbecue pits, brush
piles, etc. To avoid spreading fire, do not
use blower near leaf or brush fires, fire-
places, barbecue pits, ashtrays, etc.
D
Always use collection bag shoulder strap
when vacuuming to avoid loss of control.
D
Check air intake openings, elbow tube,
and vacuum tubes frequently, a lways
with the unit stopped and the power
source disconnected. Keep vents and
tubes free of debris which can accum u-
late and restrict proper air flow. Do not
use with any opening blocked. Keep free
of dust, lint, hair and anything that may re-
duce air flow.
STANDARDS
This product is listed by Underwriter’s Lab-
oratories, Inc., in accordance with UL Stan-
dard 1017.
If situations occur which are not covered in
this manual, use care and goodjudgement.
If you need assistance, contact your Autho-
rized Service D ealer or call
1-800-554-6723. Failure to follow all Saf ety
Rules and Precautions can result in serious
injury.
SAVE THESE INSTRUCTIONS
ASSEMBLY
WARNING:
Unplug the unit be-
fore opening the vacuuminlet cover or at-
tempting to insert or remove the inlet re-
strictor, blower tubes or vacuum tubes.
The motor must be stopped and the im-
peller blades no longer turning to avoid
serious injury from the rotating blades.
WARNING:
If you receive your
unit assembled, check each step to in-
sure your unit is properly assembled and
all fasteners are secure. Follow all safety
information i n the manual and on unit.
S
A standard screwdriver is required for
assembly.