Filter
Top Products
72
2015 Toro Commercial Equipment Guide 15-003-T Rev. 2/15
REELMASTER 5510,
MODEL 03676
REELMASTER 5510-G,
GAS, MODEL 03609
REELMASTER 5510-D (A),
TIER 4 DIESEL, MODEL 03607
ENGINE
Kubota
®
4-cylinder, liquid cooled, diesel engine.
35.5 hp (26.5 kW) @ 3000 rpm.
Kubota
®
4-cylinder, liquid cooled, gas engine.
49 hp (36.5 kW), 88.5 ft. lbs. (120 Nm) torque.
Yanmar
®
3-cylinder, liquid cooled, diesel engine.
36.8 hp (27.5 kW), 74.4 ft. lbs. (105 Nm) torque,
1.64 liter displacemen
t.
LUBRICATION
Pressurized lubrication system with 5.0 quart (4.7 liter) capacity.
FUEL FILTER
Replaceable spin-on fuel filter/water separator.
AIR CLEANER
Heavy-duty three-stage, radial seal air cleaner with restriction indicator.
COOLING
Rear mounted radiator with industrial tube and fin
construction, 6.5 fins per inch, 7.0 quart (6.6 liter) capacity.
Plate and bar radiator/oil cooler combination, 6.3 fins per inch, 10 quart (9.5 liter) capacity.
FUEL TANK CAPACITY
13.5 gallon (51.1 liter) capacity. Biodiesel-Ready for use
up to B-20 (20% biodiesel and 80% petroleum blend).
14 gallon (53 liter) capacity.
HYDRAULIC OIL CAPACITY
9.0 gallon (34.1 liter) capacity. 15 gallon (56.8 liter) capacity.
TRACTION DRIVE
Front drive wheels powered by a hydrostatic pump with individual wheel motors. All-wheel drive optional with CrossTrax
®
All-Wheel Drive system, which transfers
power from the front wheels to the opposite rear wheels via independent rear wheel motors
GROUND SPEED
0-10 mph (0-16 km/hr) forward transport; 0-8 mph (0-12.8 km/hr) mow; 0-4 mph (0-6.4 km/h) reverse.
TIRES
Front traction tires: 26.5 x 14-12 turf tires Rear steer tires: 20 x 12-10
MAIN FRAME
High strength steel frame with welded construction.
BRAKES
Individual left and right drum-type front wheel brakes. Brakes may be actuated for service braking via left foot pedal. Integrated foot pedal lock provides parking
brake. Dynamic braking through hydrostatic traction drive system.
STEERING
Rear wheel, power steering with an independent hydraulic pump and circuit.
GAUGES
InfoCenter
TM
onboard LCD display shows gauges, alerts/faults, service reminders, electrical system diagnostics, indicates fuel level, coolant temp., low oil pressure,
alternator, engine hours, engine rpm, voltage, reel speed, backlap speed, glow indicator (diesel), lift/lower indicator.
CONTROLS
Single foot-operated traction pedal, foot actuated mow speed limiter, foot
actuated service and parking brake. Hand-operated key ignition switch,
throttle, cutting unit raise/lower joystick, cutting unit engage switch, and
headlight switch all positioned on right hand pivoting control console.
Single foot-operated traction pedal, foot actuated mow speed limiter, foot actuated service and parking
brake. Hand-operated key ignition switch, throttle, isochronous engine speed control, cutting unit raise/
lower joystick, cutting unit engage switch, and headlight switch all positioned on right hand pivoting
control console.
ELECTRICAL & INTERLOCKS
Heavy-duty 12-volt battery, 570 CCA, 40 amp alternator. Electronic control unit is a microprocessor based,
solid state control unit with diagnostic capabilities. Traction pedal, parking brake, operator presence in seat,
and cutting unit engage/disengage safety interlock switches.
Heavy-duty 12-volt battery, 570 CCA, 55 amp alternator.
Electronic control unit is a microprocessor based, solid state
control unit with diagnostic capabilities. Traction pedal, parking
brake, operator presence in seat, and cutting unit engage/
disengage safety interlock switches.
REEL DRIVE
Reel drive circuit is split independently for front and rear cutting units. Hydraulic functions controlled by an integrated hydraulic control block. Reel speeds are
electronically adjustable in nine incremental settings. Standard on-board backlapping.
CUTTING UNIT LIFT/LOWER
Front and rear cutting unit lift/lower is sequenced for uniform starting and ending points.
SEAT
Deluxe high back suspension seat with fore, aft, height and weight adjustment.
ROPS
Standard with seat belt
HEIGHT
63" (160 cm) seat top, 85.5" (217.2 cm) top of ROPS.
LENGTH (2WD)
111" (281.9 cm)
WHEEL BASE
60" (152.4 cm)
OPERATIONAL WIDTH
116" (288.3 cm)
TRANSPORT WIDTH
92" (233.7 cm)
WEIGHT
2,693 lbs. (1,222 kg) (2WD), 2,803 lbs. (1,271 kg) (4WD) 2,938 lbs. (1,332 kg) (2WD), 3,048 lbs. (1,382 kg) (4WD) 3,131 lbs. (1,420 kg) (2WD), 3,241 lbs. (1,470 kg) (4WD)
CERTIFICATION
Complies with ANSI B71.4-2004 and CE requirements. Certain machine configurations require rear weight kits for standards compliance, see Operator’s Manual for details.
WARRANTY
Two-year limited warranty. Refer to the Operator’s Manual for further details.
Reelmaster
®
5510 / 5510-G / 5510-D Specifications
*
* Specifications and design subject to change without notice. Products depicted in this literature are for demonstration purposes only.
Actual products offered for sale may vary in use, design, required attachments and safety features. See distributor for details on all warranties.
The Reelmaster 5510 is manufactured
in Tomah, WI ISO 9002 Certified Plant.