Filter
Top Products
50
2015 Toro Commercial Equipment Guide 15-003-T Rev. 2/15
Greensmaster
®
3150-Q Specifications
*
8 BLADE DPA CUTTING UNITS, 04618
11-BLADE DPA CUTTING UNITS, 04619 14-BLADE CUTTING UNITS, 04624
TRACTOR
These cutting units will mount on any Toro riding Greensmaster (excluding Greensmaster TriFlex
TM
33xx/34xx series).
HEIGHT OF CUT
(HOC) RANGE
Cutting height is adjusted on front roller by two vertical screws and held by two locking cap screws. Bench HOC range is .062"-.297" (1.6-7.5 mm). With high HOC kit,
range is .285-1" (7.3-25.4 mm). Effective HOC may vary depending on turf conditions and bedknife installed.
REEL WELDMENT
Reels are 5" (13 cm) in diameter, 21" (53.3 cm) in length. High carbon steel blades are welded to 5 stamped steel spiders, and heat treated. The reel is ground for
diameter and concentricity, and relief ground.
REEL BEARINGS
Two stainless steel ball bearings, 30 +/-.1 mm inside diameter slip fit onto reel shaft retained by internally splined threaded insert. Low drag seals/slingers for added
protection with o-ring sealed motor and counterweight. Reel position maintained by a wave washer with no adjusting nut.
MAINTENANCE
No grease zerks, sealed bearing design eliminates daily maintenance.
REEL DRIVE
The reel weldment shaft is a 1.375" (35 mm) diameter tube with internally splined threaded insert.
FRAME
Precision machined, die-cast aluminum cross member with two bolt-on die-cast aluminum side plates.
AGGRESSIVENESS
Aggressiveness stays constant throughout the life of the reel. Patented design.
BEDKNIFE
Replaceable single edged EdgeMax
TM
Microcut Bedknife is standard.
BEDKNIFE ADJUSTMENT
Dual screw, indexed “click” adjustment to the reel; detents corresponding to .0007" (.018 mm) bedknife movement for each position.
FRONT & REAR ROLLERS
Front: Not included with cutting unit, purchased separately. Option between full, narrow-spaced and wide-spaced Wiehle roller.
Rear: Steel full, 2" (5.1 cm) diameter with sealed bearings and through-shaft.
GRASS SHIELD
Non-adjustable shield with adjustable cut-off bar to improve grass discharge from reel in wet conditions.
TOTAL WEIGHT
8-blade: 72 lbs. (32.7 kg) with aluminum Wiehle Roller. 11-blade: 75 lbs. (34 kg) with aluminum Narrow Wiehle Roller.
14-blade: 78 lbs. (35 kg) with aluminum Wiehle Roller.
GREENSMASTER 3150-Q, MODEL 04358
ENGINE
18 hp (13.4 kW) @3600 rpm, Briggs & Stratton
®
gasoline engine, governed to 2850 rpm high idle, 1650 rpm low idle. Air-cooled.
FUEL CAPACITY
7 gallon (26.5 liter) capacity; unleaded gasoline.
TRACTION DRIVE
Hydraulic piston pump, closed loop system. 2WD Parallel Hydrostatic or 3WD Series Parallel piston pump closed loop system. Foot pedal forward and reverse; infinitely variable.
GROUND SPEED
Forward-mowing speed is variable from 2-5 mph (3.2-8 km/h), adjusted by stop on pedal mechanism. Mow speed setting does not affect transport speed. Maximum
Greensmaster 3150-Q transport speed is 8.8 mph (14.4 km/h), may be reduced by adjusting stop in footrest pan without affecting mow speeds. Reverse is 2.5 mph
(4.0 km/h) maximum.
TURF COMPACTION
8-10 psi (dependent on tire pressure) with operator and cutting units down.
IMPLEMENT DRIVE
Single gear pump, mono valve block, series reel drive to 3 motors.
STEERING
Power steering. Adjustable steering wheel tilt and a 5-position steering arm tilt.
CONTROLS/GAUGES
Raise/lower-mow lever (joystick). Functional control lever (neutral, mow, transport). Foot operated traction drive and brakes. Hour meter. Hand operated throttle and
choke. Mechanical engine speed control.
ELECTRICAL FEATURES
12-volt lead acid, group size U1, with 300 minimum cold cranking amps at 0° F and 34 minutes reserve capacity at 85° F/25 amps draw. 16 amp alternator. Ignition
switch/key. Seat switch. Harness terminals and fuse slot available for optional lights installation.
TIRES/WHEELS/PRESSURE
Three tires: Three 18 x 10.5-8, 4-ply pneumatic tubeless demountable and interchangeable with smooth tread.
8-12 psi front; 8-15 psi rear. Optional Traction Tire (4-ply): P/N 119-3516.
BRAKES
Two 6" (15.2 cm) drum type.
HYDRAULIC OIL
7.5 gallon (28.4 liter) tank with internal baffle. 1.0 gallon (3.8 liter) auxiliary tank.
LEAK DETECTION
Equipped with Turf Guardian™ leak detection system.
SOUND LEVEL
82 dB(A) at operator’s ear under normal conditions.
OVERALL DIMENSIONS
Wheel Tread: 49.5" (149.9 cm), Wheel Base: 47" (119 cm), Length: 90" (229 cm), Width: 69.7" (177 cm) w/reels, Height: 74.5" (189 cm), Weight: 1,087 lbs. (493 kg).
WIDTH OF CUT
59" (150 cm)
REEL SPEED
Approximately 1975 RPM at 2850 engine RPM. Adjustable.
BACKLAPPING
Standard equipment.
CUTTING UNIT SUSPENSION
Cutting units are completely free-floating, each attaching to the tractor by direct pull links and lifted by a centered lift arm. Baskets are supported by carrier frames
that are ground following. Cutting unit floatation is unaffected by basket content. Grass baskets are all interchangeable and accessible from the front of the machine.
ROPS
Roll Over Protection System standard.
CERTIFICATION
Certified to meet ANSI specification B71.4-2012 and European CE standards with appropriate kits installed.
WARRANTY
Two-year limited warranty. Refer to the Operator’s Manual for further details.
The Greensmaster 3150-Q is manufactured in
Tomah, WI ISO 9002 Certified Plant.
* Specifications and design subject to change without notice. Products depicted in this literature are for
demonstration purposes only. Actual products offered for sale may vary in use, design, required attachments
and safety features. Consult your local Toro Distributor.