Filter
Top Products
SPECIFICATIONS COMMON TO WORKMAN HD SERIES VEHICLES
FRONT SUSPENSION
Independent system with dual “A” frame control arms, dual coil springs and dual shock absorbers with anti-sway bar. Provides 5 3/4” travel.
REAR SUSPENSION
DeDion rear axle (weight carrying axle) suspension independent of transaxle with dual leaf springs and dual shock absorbers. Provides 3” travel.
BATTERY
12-volt, group 26, with 540 cold cranking amps at 0 degrees F (-18 degrees C).
TRANSMISSION
Rear transaxle directly connected to engine, twin axle drive. 3-speed synchromesh (forward speeds only), h-shift pattern with high-low range providing
6 forward speeds and 2 in reverse. Transmission housing doubles as hydraulic reservoir with outlet screen and external filter.
3RD HIGH LOCKOUT
Interlock key switch that prevents engine from running in 3rd gear, high range.
DIFFERENTIAL LOCK
Manual engage rear differential lock.
4WD SYSTEM
Fully automatic on-demand, bi-directional system. Uses dual bi-directional clutches. In event of rear tire slippage, clutches transmit power proportionally to
front wheel with highest traction.
FRAME
Steel space frame front frame and C-channel rear frame.
STEERING
Hydraulic power steering with with steering valve coupled to hydraulic cylinder with thru shaft. Maximum steering angle is 70 degrees on 2WD
and 50 degrees on 4WD.
2-POST ROPS
2-post rollover protective structure and protective back panel bolted to ROPS.
BRAKES
4-wheel hydraulic disk brake system. 9 1/2” disk with hydraulic service brakes using twin piston fix mount calipers. Parking brake uses mechanical cable
actuated caliper on rear wheels.
HYDRAULICS
4 gpm (15 lpm) gear pump provides hydraulic flow for power steering and lift in series. Lift control valve with quick disconnects for dual lift cylinders or for
attachments when quick disconnects are switched. 8 quart total capacity.
LIGHTS
Twin halogen headlights and dual taillights actuated by switch on dash. Dual brake lights actuated by brake pedal.
SEAT BELTS / SEATS
Lap seat belts standard. Bucket seats with adjustable slides to allow for various seat positions. Hip restraint tubes welded to seat mounting straps.
CONTROLS
Throttle, brake and clutch pedals. Gear shifter, differential lock, parking brake, high-low range shifter and hydraulic lift levers.
INTERLOCK
To start engine, clutch pedal must be depressed and remote hydraulic lever must be in neutral position. If installed, high flow hydraulics and rear PTO must
be disengaged / switched off.
SAFETY SUPPORT
7-gauge steel channel stores behind seat and fits over extended lift cylinder to prevent accidental lowering of bed.
GROUND CLEARANCE
7” (18 cm) with no load.
REAR TOW HITCH
Steel hitch bracket bolted to rear DeDion axle. Mounting plate provides mounting hole for pin or ball hitch and incorporates two safety chain mounting holes.
Maximum tongue weight of 600 lbs (272 kg). Maximum trailer weight of 3500 lbs (1587 kg). Trailers over 1500 lbs. require trailer brakes.
GROUND SPEED
Standard Tires, Gear 1/2/3
Forward Speeds: High Range 7.6/11.5/19.8 mph (12.2/18.5/31.9 km/h)
Low Range 2.9/4.5/7.7 mph (4.7/7.2/12.5 km/h)
Reverse Speeds: High Range 7.1 mph (11.6 km/h)
Low Range 2.8 mph (4.5 km/h)
DIMENSIONS
Overall Length Overall Width Overall Height (Top of ROPS)
127.6 in (324 cm) w/o bed 64.7 in (164.3 cm) 75.8 in (192.5 cm)
130 in (330 cm) w/ full bed
CERTIFICATIONS
Certified to meet SAE J2258. Certified to meet ISO/DIS 21299 for ROPS. Engine meets all applicable emission standards per the manufacturer. Certified to
meet the CE Machinery Directive.
WARRANTY
Two-year limited warranty. See Operator’s Manual for further details.
Workman
®
HD/HDX Series Specifications (continued)
Specifications subject to change. Please contact your Toro distributor for details.