Stiga 45 Lawn Mower User Manual


 
7
ENGLISH
GB
COOLING SYSTEM
Before use, the engine's cooling system should be
cleaned. Clean the cylinder's cooling fins and the
air intake, removing any grass cuttings, dirt and the
like.
CHANGING OIL
Change the oil when the engine is warm
and the petrol tank is empty. Hot oil will
run out of the engine better. Use caution
when draining the hot oil, as it could
cause burn injuries.
Change the oil the first time after 5 hours of oper-
ation, and subsequently after every 50 hours of op-
eration or once a season. Remove the dip stick, tilt
the mower and let the oil run out into a container.
Becarefulnottoletanyoilrunontothegrass.
Fill with new oil: use oil of SAE 30 or SAE 10W-
30 quality. The crankcase holds approx. 0.6 litre.
Fill until the oil reaches the "FULL/MAX" mark
on the dip stick.
AIR FILTER
A dirty and blocked air filter reduces the engine
output and increases engine wear.
Carefully remove the air cleaner so that no dirt
falls down into the carburettor (fig. 11). Take out
the foam plastic filter element and wash it in liquid
detergent and water. Dry the filter element. Pour a
little oil on the filter element and squeeze it in. Re-
fit the air cleaner.
Wash the filter every three months or every 25
hours running, whichever comes first, or more fre-
quently if used in dusty conditions.
SPARKING PLUG
Neverremovethesparkplugortheigni-
tion lead when checking to see if there is
any spark, always use an approved test
instrument.
Clean the sparking plug regularly (every 100 hours
running). Use a wire brush for cleaning and adjust
the correct spark gap (fig. 12).
Change the sparking plug if the electrodes are ex-
cessively burnt or if the plug is damaged. The rec-
ommendations of the engine manufacturers are as
follows:
Champion J19LM (RJ19LM) or another equiva-
lent spark plug ought to be used in Briggs & Strat-
ton engines. Spark gap 0.76 mm.
CHANGING BLADES
Useprotectiveglovestopreventcuts
when changing the blade.
Blunt and damaged blades tear off the grass and
spoil the look of the lawn after mowing. New, well
sharpened blades cut the grass cleanly, so that the
lawn looks green and fresh even after mowing.
Always check the blade after an impact. First dis-
connect the ignition cable. If the blade system has
been damaged the defective parts must be
changed. Always use genuine spare parts.
To replace the blade, slacken the blade bolt. Fit the
new blade so that the stamped STIGA logotype is
turned facing the blade attachment (and not facing
the grass). Refit the washer and blade bolt. Tighten
the blade bolt fully to a torque of 40 Nm (fig. 13).
When replacing the blade, the blade bolt should
also be replaced.
The guarantee does not cover damage to the blade,
blade holder or engine caused by running into ob-
stacles.
When replacing the blade, the blade holder and
blade bolt, always use original spare parts. Non-
authentic spare parts could lead to the risk of per-
sonal injury or damage, even if they fit the ma-
chine.
SHARPENING OF THE BLADE
Sharpening of the blade must be done by wet meth-
od grinding, using a whetstone or a grindstone.
For the sake of safety, the blade should not be
sharpenedonanemerywheel.Averyhightemper-
ature could cause the blade to become brittle.
Once the blade has been sharpened, it
must then be balanced so as to avoid vi-
bration damage.
STORAGE
WINTER STORAGE
Empty the fuel tank. Start the engine and let it run
until it stops. The same petrol must not remain in
the tank for more than one month.