Snapper 10287E Snow Blower User Manual


 
Handles and Controls Group
Footnotes:
TP 400-5044-2-LF-N
Manual No. 7006079TWO STAGE LARGE FRAME
(2005) SERIES 7
5
Part No Descri
p
tionItem Qt
y
Note
1 1726833 1 CABLE AND SPRING ASSEMBLY, R.H. Auger
2 1701996 1 SPRING, Torsion
3 1727087A 1 HANDLE, Tube, R.H.
4 7091908 1 CAPSCREW, Hex Head, 5/16-18 x 1-3/4 G5 Was 1922127
5 7091540 3 CAPSCREW, Hex Head, 5/16-18 x 1-1/2 G5 Was 1921221
6 1960671 2 SCREW, Pan Head Torx, 1/4-20 x 3/4, Thread Cutting
7 1715654 2 SPACER, 1/4ID x 25/64OD x 11/64LG
8 1922837 2 CAPSCREW, Hex Head, 1/4-20 x 1-1/2 G5
9 1722638 1 HANDLE, Clutch R.H.
10 1715655 2 SPACER
11 1923358 2 NUT, Hex Centerlock, 1/4-20
12 1726317 2 GRIP see Note 1
13 1723965 2 HAND GRIP, Heated 1” Diameter see Note 2
14 1726422 2 RIVET, Pop see Note 2
15 1923341 1 CAPSCREW, Hex Head 1/4-20 x 3/4 G5 see Note 2
16 1724037 1 RESISTOR BLOCK, 2 Male Terminal see Note 2
17 1723967 1 SWITCH, Hand Warmer see Note 2
18 1725409 1 HARNESS, Wiring see Note 2
19 1715956 1 CLIP, Wire see Note 2
20 1726983A 1 DASH AND SUPPORT ASSEMBLY, Tubular
21 1667588 4 BUSHING, 47/125ID x 437/1000OD x 1/5LG see Note 1
22 1714084 1 KNOB, Spinner see Note 1
23 1960093 1 NUT, Push Pal, 3/8” Diameter Stud Capped see Note 1
24 1722633 1 ROD AND SPRING ASSEMBLY, w/Pin
25 1722690 1 SPRING, Complete
26 1960519 1 PUSH NUT, Stud Cap, 1/2
27 1722630 1 ROD, 4/25” Diameter, E-Coat
28 1722667 1 HANDLE, Clutch L.H.
29 1727086A 1 HANDLE, Tube, L.H.
30 1960662 1 CAPSCREW, Hex Head, 1/4-20 x 2 G5
31 1920397 2 NUT, Hex Lock ESNA Light, 1/4-20NC-3B
32 1921319 2 WASHER, 1/4
33 1933896 1 NUT, Hex Lock, 10-24
34 1722631A 1 LEVER, Pivot
35 1718791 1 CABLE AND HANDLE ASSEMBLY, Clutch
36 1725702 1 SCREW, Pan Head Torx, #10 x 1/2 Thread Cut
37 1726995 1 SPACER, 1-1/4 LG Beveled End
Note 2: Used on 12387E, E12387
Note 1: Used on all models exept 12387E, E12387