Remington Power Tools 104316-04, 104316-05, 106890-01, 106890-02, 108526-01, 104317, 106821, 106821A Chainsaw User Manual


 
21
108539
www.desatech.com
4. Hold file guide level. Make sure 30° mark on
file guide is parallel to center of guide bar (see
Figure 19). This will insure that you file cutters
at 30° angle.
5. File from inside towards outside of cutter until
sharp. Only file in this one direction (see Figure
19). Note: Two or three strokes with file should
sharpen cutter.
6. After each cutter is sharpened, move chain for
-
ward to sharpen next cutter. File all cutters on
one side of chain.
7. Move to other side of chain and repeat process.
Filing Cutter Depth Gauges
The cutter depth gauge clearance is reduced as cutters
are sharpened. After every second or third sharpen
-
ing, reset cutter depth gauges.
1. Place depth gauge tool (.025") firmly across top
of two cutters. Make sure depth gauge enters slot
in depth gauge tool (see Figure 21).
2. Use medium flat file. File depth gauge level with
depth gauge tool.
3. Remove depth gauge tool. With flat file, round
off front corner of cutter depth gauge (see Figure
22).
After several hand filings, have authorized service
center or sharpening service machine sharpen chain.
This will insure even filing.
REPLACING SAW CHAIN
Replace chain when cutters are too worn to sharpen or
when chain breaks. Only use replacement chain noted in
this manual. Always include new drive sprocket when
replacing chain. This will maintain proper driving of
chain. Note: For proper chain and drive sprocket, see
Replacement Parts and Accessories
.
CLEANING AND
MAINTENANCE
Continued
WARNING: Use only replacement parts
and accessories described in this manual.
Use of other parts or accessories could
damage saw or injure operator.
STORAGE
If storing saw for more than 30 days, follow steps below.
1. Drain oil tank.
2. Remove and clean guide bar and chain. Clean
guide bar and chain by soaking in petroleum
based solvent or mild soap and water mixture.
3. Dry guide bar and chain.
4. Place chain in container filled with oil. This will
prevent rust.
5. Wipe a thin coating of oil over surface of guide bar.
6. Wipe off outside of saw body. Do this with soft cloth
dampened with a mild soap and water mixture.
7. Store chain saw
• in a high or locked place, out of children’s reach
• in a dry place
• in a carrying case or with scabbard over guide bar
Continued
TECHNICAL SERVICE
You may have further questions about assembling,
operating, or maintaining this product. If so, you
can visit our Technical Service web site at www.
desatech.com or contact our Technical Service
Department at 1-800-858-8501 (English Only). You
may also write to:
DESA Specialty Products™
P.O. Box 90004
Bowling Green, KY 42102-9004
ATTN: Technical Service Specialty Products
When contacting DESA Specialty Products™, have
ready
Your Name
Your Address
Your Phone Number
Model Number of Product
Date of Purchase (Include copy of receipt for
written requests).
REPLACEMENT PARTS
AND ACCESSORIES
For original replacement parts and accessories, con-
tact your nearest Authorized Dealer or Authorized
Service Center for this product. If they can not sup
-
ply the part or accessory, contact your nearest Parts
Central listed on page 47. Each Authorized Dealer,
Authorized Service Center, and Parts Central is
independently owned and operated.
See pages 48 and 49 for an Illustrated Parts List.
If you need additional referral information, contact our
Technical Service Department (see Technical Service).
In Canada call 1-800-561-3372 for parts information.
You may purchase the following service or replace
-
ment parts:
LNT-2
Part Number
Description
104302-01S
#
Guide bar, 8" (20.3 cm)
104301S
#
Chain, 8" (20.3 cm)
097567-01S Guide bar, 10" (25.4 cm)
091371S Chain, 10" (25.4 cm)
097568-02S Guide bar, 12" (30.5 cm)
091373-02S Chain, 12" (30.5 cm)
075752 Drive Sprocket
#
Must order both pieces