Filter
Top Products
5
Symmetrical GuideBar
Large RadiusTip
S Low--Kickback Chain, designed with a
contoured depth gauge and guard link
which deflect kickback force and allow
wood t ogradually rideintothecutter.Low--
Kickback Chain has met kickback per-
formance requirements when tested on a
representative sample of chain saws be-
low 3.8 cubic inch displacement specified
in ANSI B175.1.
Low--- Kickback
Chain
Not a Low--- Kickback Chain
Can Obstruct Material
Contoured Depth Gauge
Elongated Guard Link
Deflects
kickback force
and allows wood
to gradually ride
into cutter
S Front Hand Guard, designed to reduce the
chance of your left hand contacting thechain
if your hand slips off the front handlebar .
S Position of front and rear handlebars, de-
signed withdistancebetweenhandles and
“in-line” with each other. The spread and
“in-line” position of the hands provided by
this design work together to give balance
and resistance in controlling the pivot of
the saw back toward the operator if kick-
back occurs.
CHAIN BRAKE AND CKA ANGLE
S Chain Brake, designed tostop thechainin
the event of kickback.
WARNING: WE DO NOT REP-
RESENT AND YOU SHOULD NOT AS-
SUME THA T THE CHAIN BRAKE WILL
PROTEC T Y OU IN T H E EV EN T OF A K I CK-
BACK. Kickback is a lightning fast action
which throws the bar and rotating chain back
and up toward the operator. Kickback can be
caused by allowing contact of the bar tip i n the
danger zone with any hard object. K ickback
canalsobecausedbypinchingthesawchain
along the top of the guide bar . This action may
push the guide bar rapidly back toward the op-
erator. Either of these events may cause you
to lose control of the saw which could result in
serious injury or even death. DO NOT RELY
UPON AN Y O F THE D E VI CES BUI LT INTO
YOUR SAW . YOU S HOULD USE THE SAW
PROPERL Y AND CAREFULLY TO A VOID
KICKBACK. Re duced--kickback guide b ars
and low--kickback saw chains reduce the
chance and magnitude of kickback and are
recommended. Your saw has a low kickback
chain and bar as original equipment. Repairs
on a chain brake should be made by an autho-
rized servicing dealer . Take your unit t o the
place of purchase if purchased from a servic-
ing dealer , or to the nearest authorized master
service dealer.
S Tipcontact insomecases may cause alight-
ning fast reverse REACTION, kicking guide
bar up and back toward operator.
S Pinching the saw chain along the top of the
guide bar may push the guide bar rapidly
back toward the operator.
S Either of these reactions may cause you to
lose control of the saw which could result in
serious injury. Do not rely exclusively upon
devices built into your saw.
WARNING: C omputed kickback
angle (CKA) listed on yoursaw and listed inthe
CKA table below represents angle of kickback
your bar and chain combinations will have
when tested in accordance with CSA (Cana-
dian Standards Association) and ANSI stan-
dards. When purchasing replacement bar and
chain, considerations should be given to the
lower CKA values. Lower CKA values repre-
sent safer angles to the user , higher values in-
dicate more angle and higher kick energies.
Computed angles represented indicate total
energy and angle associated without activation
of the chain brake during kickback. Activated
angle represents chain stopping timerelativeto
activation angle o f chain break and resulting
kick angle of saw . In all cases lower CKA val-
ues represent a safer operating environment
for the user .
The f ollowing guide bar and chain combina-
tions meet kickback requirements of CSA
Standards Z62.1, Z62.3, & ANSI B175.1
when used on saws listed i n this manual.
Use of bar and chain combinations other
than those listed is not recommended and
may not meet the CKA requirements per
standard.
Computed kickback angle (CKA) Table
BAR
P/N Length CHAIN P/N
952044368 14″
MODEL
CKA without chain brake
S1970
33_
952051209
NOTE: Ifthissawistobeusedforcom-
mercial logging, a chain brake is required
and shall not be removed or otherwise dis-
abled tocomply with Federal OSHA Regula-
tions for Commercial Logging.
SAFETY NOTICE: Exposure to vibrations
through prolonged use of gasoline powered
hand tools could cause blood vessel or nerve
damage in the fingers, hands, and joints of
people prone to circulation disorders or
abnormal swellings. Prolonged use in cold
weather has been linked to blood vessel