Poulan S1838 Chainsaw User Manual


 
14
dusty conditions. A used aire filter can never
be completely cleaned. It is advisable to re-
place your air filter with anew one after every
50 hours ofoperation, or annually,whichever
comes first.
1. Loosen 3 screws on cylinder cover.
2. Remove cylinder cover.
3. Remove air filter.
4. Clean the air filter using hot soapy water.
Rinse with clean cool water. Air dry com-
pletely before reinstalling.
5. Lightly oil air filter before installing to im-
prove t he efficiency of air filter. Use
2 --cycle engine oil or motor oil (SAE 30).
Squeeze excess oil from f ilter.
6. Reinstall air filter.
7. Reinstall cylinder cover and 3 screws.
TIghten securely.
Air Filter
Cylinder Cover
Screws
Cylinder
Cover
INSPECT MUFFLER AND SPARK
ARRESTING SCREEN
As the unit is used, carbon deposits build up
on the muffler and spark arresting screen,
and must be removed to avoid creating afire
hazard or affecting engine performance.
Replace the spark arresting screen if breaks
occur.
Muffler Diffuser
Muffler
Cover
Screws
Muffler
Cover
Muffler
Body
Spark
Arresting
Screen
CLEANING THE SPARK ARREST-
ING SCREEN
Cleaning is required every 25 hours of op-
eration o r annually, whichever comes first.
1. Loosen and remove the 2 muffler cover
screws.
2. Remove the muffler cover (cover snaps
off muffler body).
3. Remove muffler diffuser and spark ar-
resting screen assembly. Notice the
orientation of these parts for reassem-
bling.
4. Clean the spark arresting screen with a
wire brush. Replace screen if breaks are
found.
5. Replace any broken or cracked muffler
parts.
6. Reinstall diffuser and spark ar resting
screen assembly with round holes facing
up.
7. Reinstall muffler cover and 2 screws.
Tighten securely.
CARBURETOR ADJUSTMENT
WARNING:
The chain will be mov-
ing during most of this procedure. Wear your
protective equipment and observe all safety
precautions. The chain must not move at idle
speed.
The carburetor has been carefully set at the
factory. Adjustments may be necessary if
you notice any of the f ollowing conditions:
S
Chain moves at idle. See IDLE SPEED--T
adjusting procedure.
S
Saw will not idle. See IDLE SPEED--T ad-
justing procedure.
Idle Speed--T
Allow engine to idle. If the chain moves, idle
is too fast. Ifthe engine stalls, idle is too slow.
Adjust speed until engine runs without chain
movement (idle too fast) or stalling (idle too
slow). The idle speed screw is located in the
area above the primer bulb and is labeled T.
S
Turn idle speed screw (T) clockwise to in-
crease engine speed.
S
Turn idle speed screw (T) counterclock-
wise to decrease engine speed.
If you require further assistance or a re unsure
about per form ing t his procedure, contact your
authorized service dealer or call
1--800--554--6723.
BAR MAINTENANCE
If your saw cuts to one side, has to be forced
through the cut, or been run with an improper
amount of bar lubrication it may be neces-
sary toservice your bar . A wornbar will dam-
age your c hain and make cutting difficult.
After each use, ensure ON/STOP switch is
in the STOP position, then clean all sawdust
from the guide bar and sprocket hole.
To maintain guide bar:
S
Move ON/STOP switch to the STOP posi-
tion.
S
Loosen and remove chain brake nuts and
chain brake. Remove bar and chain from
saw.
S
Clean the oil holes and bar groove after
each 5 hours of operation.
Remove Sawdust From
Guide Bar Groove
Oil Holes
S
Burring of guide bar rails is a normal
process of rail wear. Remove these burrs
with a flat file.
S
When rail top is uneven, use a flat file to re-
store square edges and sides.