Filter
Top Products
13
Hub
Line in Notch
Line in Notch
Line exit holes
5. Wind the line evenly and tightly onto the
spool. Wind in the direction of the ar rows
found on the spool.
6. Push thelines into thenotches, leaving 3
to 5 inches (7 -- 12 cm) unwound.
7. Insert the lines into the the exit holes in
the hub as shown in the illustration.
8. Align the notches with the line exit holes.
9. Push spool into hub until it snaps into
place.
10. Pull thelines extendingoutsideof thehub
to release the lines from the notches.
CARBURETOR ADJUSTMENT
W ARNING:
Keep othersaway when
making idle speed adjustments. The t rimmer
head or any optional attachment will be spin-
ningduringmost ofthisprocedure. Wearyour
protective equipment and observe all safety
precautions. After making adjustments, the
trimmer head or any optional attachment
must not move/spin at idle speed.
The carburetor has been carefully set at the
factory.Adjustments maybenecessaryif you
notice any of the following conditions:
S
Engine will not idle when the throttle is
relea se d.
S
The trimmer head or any optional
attachment moves/spins at idle.
Make adjustments with the unit supportedso
the cutting attachment is off the ground and
will not make contact with any object. Hold
theunit b yhandwhile runningandmakingad-
justments. Keep all parts of your body away
from the cutting attachment and muffler.
Idle Speed Adjustment
Allow enginetoidle. A djustspeed untilengine
runs without trimmer head or any optional at-
tachment moving or spinning (idle too fast) or
engine stalling (idle speed too slow).
S
Turn idle speed screw clockwise to
increase engine speed if engine stalls or
dies.
S
Turn idle speed screw counterclockwise to
decrease engine speed if trimmer head or
any optional attachment moves or spins at
idle.
W ARNING:
Recheck the idle speed
after each adjustment. The trimmer head or
any optional attachment must not move or
spin atidle speedtoavoid s eriousinjury tothe
operator or others.
Idle Speed
Screw
Air Filter
Cover
Ifyou requirefurtherassistanceor areunsure
about performing this procedure, contact an
authorized service dealer or call
1--800--554--6723.
STORAGE
W ARNING:
Perform the following
steps after each use:
S
Allow engineto cool beforestoring ortrans-
porting.
S
Store unit and fuel in a well ventilated area
where fuel vapors cannot reach sparks or
open flames from water heaters, electric
motors or switches, furnaces, etc.
S
Store unit with all guards in place. Position
unit so that any sharp object cannot acci-
dentally cause injury.
S
Store unit and fuel well out of the reach of
children.
SEASONAL STORAGE
Prepareunit for storage atend ofseason or if
it will not be used for 30 days or more.
If your unit is to be storedfor a period o f time:
S
Clean the entire unit before lengthy
storage.
S
Store in a clean dry area.
S
Lightly oil external metal surfaces.
FUEL SYSTEM
Under FUELING ENGINE in the OPERA-
TION section o fthis manual,seemessagela-
beled IMPORTANT regarding the use of ga-
sohol in your engine.
Fuel stabilizer is an acceptable alternative in
minimizing the formationof fuel gumdeposits
during storage. Add stabilizer to the gasoline
in the fuel tank or fuel storage container. Fol-
low the mix instructions found on stabilizer
container. Runengine atleast5 minutesafter
adding stabilizer.
HELPFUL TIP
Duringstorageof yourgas/
oil mixture,theoil will sepa-
rate from the gas.
We recommend that you
shake the gas can weekly
toinsureproperblendingof
the gas and oil.