Filter
Top Products
10
IGNITION
SWITCH
ON
STOP
Choke
Lever
1. Move ON/STOP switch to the ON posi-
tion.
2. Slowly press primer bulb 6 times.
3. Pull choke/fast idle lever out to the full
extent (to the FULL CHOKE position).
4. Pullthe starter ropesharply 5times with
your right hand. Then, proceed to the
next step.
NOTE: Iftheengine sounds asif itis trying
to start before the 5th pull, stop pulling and
immediately proceed to the next step.
5. Push the choke/fast idle lever in to the
HALF CHOKE position.
OFF
HALF
CHOKE/FAST IDLE LEVER
FULL
6. Pull the starter rope sharply with your
right hand until the engine starts.
7. Allowtheengine torun for approximate-
ly 30 seconds. Then, squeeze and re-
lease the throttle trigger to allow engine
to return to idle speed.
STARTING A WARM ENGINE
1. Move ON/STOP switch to the ON posi-
tion.
2. Slowly press primer bulb 6 times.
3. Pull th e choke/fast idle lever out to the
FULL CHOKE position to set the fast
idle, then push the lever in to the HALF
CHOKE position.
4. Pull the starter rope sharply with your
right hand until the engine starts.
5. Squeeze and release throttle trigger to
allow engine to return to idle speed.
DIFFICULT STARTING (or starting a
flooded engine)
The engine may be flooded with too much
fuel if it has not started after 10 pulls.
Flooded engines can be cleared of excess
fuel by pushing the choke/fast idle lever in
completely (to the OFF CHOKE position)
and then following the warm engine starting
procedure listed above. Ensure the ON/
STOP switch is in the ON position.
Startingcouldrequirepullingthe starterrope
handle manytimes depending onhow badly
theunitisflooded.Ifenginefailstostart,refer
tothe TROUBLESHOOTING TABLE orcall
1-800-554-6723.
CHAIN BRAKE
WARNING: Ifthebrakebandisworn
toothin itmay breakwhenthechainbrakeis
triggered. With a broken brake band, the
chainbrakewillnotstopthechain.Thechain
brake should be replaced by an authorized
servicedealer ifany partis wornto lessthan
0.020″ (0.5 m m ) thick. Repairs on a chain
brakeshouldbe madeby an authorized ser-
vicedealer.Takeyourunittotheplaceofpur-
chase if purchased from a servicing dealer,
or to the nearest authorized master service
dealer.
S This saw is equipped with a chain brake.
The brake is designed to stop the chain if
kickback occurs.
S The inert ia--activated chain brake is
activated i fthefront handguard ispushed
forward, either manually (by hand) or
automatically (by sudden movement).
S If the b rake is already activated, it is
disengagedbypullingthefronthandguard
back toward the front handle as far as
possible.
S Whencuttingwiththesaw,thechainbrake
must be disengaged.
Engaged
Disengaged
Braking function control
CAUTION:
The chain brake must be
checked several times daily. The engine
mustberunningwhenperformingthisproce-
dure. Thisis theonly instancewhenthesaw
should be placed on theground with the en-
gine running.
Place the saw on firm ground. Grip the rear
handlewithyourrighthandandthefronthan-
dle with your left hand. Apply full throttle by
fully depressing the throttle trigger. Activate
the chain brake by turning your left wrist
against the hand guard without releasing
your grip around the front handle. Thechain
should stop immediately.
Inertia activating function control
WARNING: When performing the
following procedure, the engine m ust be
turned off.
Grip therear handlewith yourrighthandand
thefronthandle withyourlefthand. Holdthe
chainsawapproximately14″ (35 cm)above
a stump or other wooden surface. Release
your grip on the front handle and use the
weightofthesawtoletthetipoftheguidebar
fallforwardandcontactthestump. Whenthe
tipofthebarhits thestump,the brakeshould
activate.