Filter
Top Products
14
S Leave the larger limbs underneath the felled
tree to support the tree as you work.
S Start at the base of the felled tree and work
toward the top, cutting branches and limbs.
Remove small limbs with one cut.
S Keep the tree between you and the chain.
Cut from the side of the tree opposite the
br a n ch you are cutt i n g .
S Remove la rger , supporting br anches w ith
the cutting techniques described in BUCK-
ING WIT HOUT A SUPPORT.
S Always use an overcut to cutsmall and free-
ly hanging limbs. Undercutting could cause
limbs to fall and pinch the saw .
PRUNING
WARNING: Limit pruning to limbs
shoulder height or below . Do not cut if
branches are higher than your shoulder . Get a
professional to do the job.
S Make your first cut
1/3 ofthe way through th e
bottom of the limb.
S Next make a 2 nd cut all t he way through
thelimb. Thencuta thirdovercut leavinga
1to2inch(2.5to5cm)collarfrom thetruck
of the tree.
First cut
Second cut
Third cut
Collar
Pruning technique
SERVICE
WARNING: Disconnect the spark
plug before performing maintenance except
for carburetor adjustments.
We recommend all service and adjustments
not listed in this manual be performed by an
authorized or Master Service Dealer.
HELPFUL TIP
IMPORTANT: Have all
repairs other than the rec-
ommended maintenance
described in the instruction
manual performed by a n
authorized service dealer.
If any dealer other than an authorized
service dealer performs work on the
product, Poulan PRO may not pay for
repairs under warranty. It is your re-
sponsibility to maintain and perform
general maintenance.
MAINTENANCE SCHEDULE
Check:
Fuel mixture level Before each use....
Bar lubrication Before each use.......
Chain tension Before each use.......
Chain sharpness Before each use.....
For damaged parts Before each use...
For loose caps Before each use......
For loose fasteners Before each use...
For loose parts Before each use......
Inspect and Clean:
Bar Before each use................
Complete saw After each use.......
Air filter Every 5 hours*.............
Chain brake Every 5 hours*.........
Spark arresting screen
and muffler Every 25 hours*..........
Replace spark plug Yearly.
Replace fuel filter Yearly...
* H ours of Operation --
Each hour of operation is approximately
2 tanks of f uel.
GENERAL RECOMMENDATIONS
The warranty on this unit does not cover
items that have been subjected to operator
abuse or negligence. To receive full value
from the warranty, the operator must main-
tainunit asinstructed inthis manual.Various
adjustmentswill need tobe madeperiodical-
ly to properly maintain your unit.
S Once a year, replace the spark plug, air filter,
and check guide bar and chain for wear . A
new spark plug and air filter assures proper
air-fuel mixture a nd he lps your engine run
better and last longer .
CHECK FOR D AMAGED OR
WORN PARTS
Contact an authorized service dealer for re-
placement of damaged or worn parts.
NOTE: It is normal fora smallamount ofoil
to appear under the saw after engine stops.
Do not confuse this with a leaking oil tank.
S ON/STOP Swit ch -- Ensu re ON/ST OP
switch functions properly by moving the
switch to the STOP position. Make sure en-
gine stops; then restart engine and continue.
S Fuel Tank -- Do not use saw if fuel tank
shows signs of damage or leaks.
S Oil Tank -- Do notusesaw ifoil tank shows
signs of damage or leaks.
CHECK FOR LOOSE
FASTENERS AND PARTS
S Bar Nuts
S Chain
S Muffler
S Cylinder Shield
S Air Filter
S Handle Screws
S Vibration Mounts
S Starter Housing
S Front Hand Guard
CHECK CHAIN SHARPNESS
A sharp chain makes wood chips. A dull
chain makes a sawdust powder and cuts
slowly. See CHAI N SHARPE NING.