Filter
Top Products
12
OPERATION
FIG. 9
MOWER BLADES -
• To stop mower blades,move attachment clutch switch
to “DIS EN GAGED” po si tion.
GROUND DRIVE -
• To stop ground drive, depress brake pedal into full
“BRAKE” position.
IMPORTANT: THE MOTION CONTROL LEVER RETURNS
TO NEUTRAL (N) POSITION WHEN THE BRAKE PEDAL IS
FULLY DEPRESSED.
ENGINE -
• Move throttle control between half and full speed (fast)
position.
NOTE: Failure to move throttle control between half and
full speed (fast) position, before stop ping may cause engine
to “backfi re”.
• Turn ignition key to “OFF” position and remove key.
Always remove key when leaving tractor to prevent
un author ized use.
• Never use choke to stop engine.
IMPORTANT: LEAVING THE IGNITION SWITCH IN ANY
POSITION OTHER THAN "OFF" WILL CAUSE THE BATTERY
TO BE DIS CHARGED, (DEAD).
NOTE: Under certain conditions when tractor is standing
idle with the engine running, hot en gine exhaust gases may
cause “browning” of grass. To eliminate this possibility, al-
ways stop engine when stopping tractor on grass areas.
CAUTION: Always stop tractor com-
plete ly, as described above, before leav-
ing the operator's position; to empty
grass catcher, etc.
TO ADJUST MOWER CUTTING HEIGHT
(See Fig. 9)
The cutting height is controlled by turning the height ad-
just ment knob in desired direction.
• Turn knob clockwise ( ) to raise cutting height.
• Turn knob counterclockwise (
) to lower cutting
height.
The cutting height range is approximately 1-1/2" to 4-1/2".
The heights are measured from the ground to the blade tip
with the engine not running. These heights are ap proxi mate
and may vary depending upon soil conditions, height of
grass and types of grass being mowed.
• The average lawn should be cut to approximately 2-1/2
inches during the cool season and to over 3 inches
during hot months. For healthier and better looking
lawns, mow often and after moderate growth.
• For best cutting performance, grass over 6 inches
in height should be mowed twice. Make the fi rst cut
relatively high; the second to desired height.
TO USE CHOKE CONTROL (See Fig. 9)
Use choke control whenever you are starting a cold engine.
Do not use to start a warm engine.
• knob in to disengage.
TO USE THROTTLE CONTROL (See Fig. 9)
Always operate engine at full throttle.
• Operating engine at less than full throttle reduces the
battery charging rate.
• Full throttle of fers the best mower per for mance.
02149
HEIGHT
AD JUST MENT
KNOB
“DRIVE”
PO SI TION
CHOKE
CON TROL
MOTION
CONTROL
LEVER
“DISENGAGED”
PO SI TION
PUSH IN TO
“DISENGAGE”
AT TACH MENT
CLUTCH SWITCH
PULL OUT TO
“ENGAGE”
IGNITION
KEY
PARKING BRAKE
“EN GAGED”
PO SI TION
THROTTLE
CONTROL
LEVER
/BRAKE PEDAL
“BRAKE”
POSITION
The operation of any tractor can result in foreign objects thrown into the eyes, which
can result in severe eye dam age. Always wear safety glass es or eye shields while op-
erating your tractor or per form ing any adjustments or repairs. We rec om mend a wide
vision safety mask over spectacles or stan dard safety glasses.
HOW TO USE YOUR TRACTOR
TO SET PARKING BRAKE (See Fig. 9)
Your tractor is equipped with an operator presence sens-
ing switch. When engine is running, any attempt by the
op er a tor to leave the seat without fi rst setting the parking
brake will shut off the engine.
• Depress brake pedal into full “BRAKE” position and
hold.
• Place parking brake lever in “ENGAGED” position
and re lease pressure from brake pedal. Pedal should
re main in “BRAKE” position. Make sure parking brake
will hold tractor secure.
TO MOVE FORWARD AND BACKWARD
(See Fig. 9)
CAUTION: Do not attempt to operate motion
control lever when the parking brake is set or
when the brake pedal is depressed. Doing so
may result in misadjustment to the drive con trol
sys tem.
The direction and speed of movement is controlled by the
motion control lever.
• Start tractor with motion control lever in neutral (N)
position.
• Release parking brake.
• Slowly move motion control lever to desired position.