Filter
Top Products
6
LOWER CHUTE (See Fig. 5)
1. Raise and hold defl ector shield in upright position.
2. Place slot in lower chute over tab on mower and position
lower chute over mower opening as shown.
3. Hook rear latch into fl ange hole on back of mower.
4. Hook front latch into tab hole on front of mower.
• If your tractor is equipped with gauge wheels on the
deck, then it will be necessary to hook the rear latch
into the hole in the R.H. gauge wheel bracket.
5
CAUTION: Do not remove defl ector
shield from mower. Raise and hold
shield when attaching lower chute
and allow it to rest on chute while in
operation.
W
AR
N
I
NG
Do
n
o
t
o
p
e
r
a
t
e
m
o
w
e
r
u
n
l
e
s
s
c
o
n
t
a
i
n
e
r
i
s
p
r
o
p
e
r
l
y
i
s
n
s
t
a
l
l
ed
.
C
o
n
t
a
i
n
e
r
i
s
s
u
b
j
ec
t
t
o
w
e
a
r
a
n
d
d
e
t
i
e
ri
o
r
a
t
i
o
n
.
Ch
e
c
k
b
a
g
f
r
e
q
u
en
t
l
y
.
Re
pl
a
c
e
w
h
en
c
r
a
c
k
e
d
o
r
d
a
m
a
g
e
d
.
Us
e
o
n
l
y
a
r
e
c
o
m
m
en
d
e
d
r
e
p
l
ac
e
m
e
n
t
c
o
n
t
a
i
n
e
r
.
W
AR
N
I
NG
Do
n
o
t
o
p
e
r
a
t
e
m
ow
e
r
u
n
l
e
s
s
c
o
n
t
a
i
n
e
r
i
s
p
r
o
p
er
l
y
i
s
n
s
t
a
l
l
e
d
.
Co
n
t
a
i
ne
r
i
s
s
u
b
j
e
c
t
t
o
w
e
a
r
a
n
d
d
e
t
i
e
r
i
o
r
a
t
i
on
.
Ch
e
c
k
b
a
g
fr
e
q
u
e
n
t
l
y
.
Re
p
l
a
c
e
w
h
e
n
c
r
a
c
k
e
d
o
r
d
a
m
a
g
e
d
.
Us
e
o
n
l
y
a
r
e
c
o
m
m
en
d
e
d
r
e
p
l
a
c
e
m
e
n
t
c
o
n
t
a
i
n
e
r
.
03022
CONTAINER MOUNTING (See Fig. 4)
1. Install one container to left side fi rst with warning to
outside of unit. Install another container to center
position and one in right position.
NOTE: Right con tain er should always over lap left con tain er
at center supports.
2. Close cover and lock latch handles over center support
tubes.
4
FIG. 4
COVER LATCH
HANDLES
CONTAINER
WARNING
CONTAINER
HANDLE
CONTAINER
WARNING
CENTER
SUPPORT
TUBES
03058
DEFLECTOR SHIELD
HINGE BRACKET
REAR LATCH
REAR GAUGE
WHEEL
BRACKET
DEFLECTOR
SHIELD
FRONT
LATCH
REAR LATCH
WITHOUT
GAUGE WHEELS
WITH REAR
GAUGE WHEELS
EXTENDED EDGE "B"
Must be under defl ector shield
and along side the hinge bracket
FIG. 5
TAB