Filter
Top Products
-- 5 --
S
To reduce noise levels, limit the number of
pieces of equipment used at any one time.
S
To reduce noise levels, operate power
blowers at the lowest possible throttle
speed to do the job.
S
Use rakes and brooms to loosen debris be-
fore blowing.
S
In dusty conditions, slightly dampen sur-
faces or use a mister attachment when wa-
ter is available.
S
Conserve water by using power blow er s
instead of hoses for many lawn and garden
applications, including areas such as gutters,
screens, patios, grills, porches, and gardens.
S
Watch outfor children, pets, open windows,
or freshly washed cars. B low debris away
safely.
S
Use the full blower nozzle extension so the
air stream can work close to the ground.
S
After using blowers and other equipment,
CLEAN UP! Dispose of debris in trash re-
ceptacles.
FUELING
WARNING:
Remove fuel cap slowly
when refueling.
This engine is certified to operate on
unleaded gasoline. Gasoline must be mixed
with a good quality synthetic 2--cycle
air--cooled engine oil designed to be mixed at
a ratio of 40:1. Poulan/Weed Eater brand
synthetic oil is recommended. (A 40:1 ratio is
obtained by mixing 3.2 ounces of oil with 1
gallon of unleaded gasoline). When mixing
fuel follow the instructions printed on the
container. Always read and follow the safety
rules under HANDLE FUEL WITH
CAUTION.
IMPORTANT
Experience indicates that alcohol blended
fuels (called gasohol or using ethanol or
methanol) can attract moisture which leads to
separation and formation of acids during
storage. Acidic gas can damage the fuel
system of an engine while in storage. Toavoid
engine problems, empty the fuel system
before storage for 30days orlonger. Drain the
gas tank, start theengine and let it run until the
fuel lines and carburetor are empty. Usefresh
fuel next season.
STARTING
TO STOP THE ENGINE
D
To stop the engine, move the throttle lever
to the STOP position.
BEFORE STARTING THE ENGINE
D
Fuel engine. Move at least 10 feet (3 me-
ters) away from the fueling site.
D
Hold the unit in the starting position as
shown. Make sure the blower end is di-
rected away from people, animals, glass,
and solid objects.
Blower
Vacuum
STARTING POSITION
WARNING:
When starting engi ne,
hold the u nit asillustrated. Donot s e tunit o nany
surface e xcept a c lean, hard a r ea when st ar ting
engine or while engine is running. Debris such
as gr avel, s and, dust, gr ass, etc. coul d be
picked up by the air intake and thrown out
through the discharge opening, damaging the
unit or property, or causing serious injury to by-
standers or the operator.
STARTING A COLD ENGINE (or a
warm engine after running out of
fuel)
S
Move throttle lever to the
position.
S
Move choke lever to the FULL CHOKE
position.
S
Slowly press the primer button 8 times.
Throttle Lever
Choke Lever
Primer Button
S
Pull starter rope sharply until engine at-
tempts to run, but no more than 5 pulls (be-
low 30
_
F, 8 pulls).
NOTE:
If engine attempts to start before the
5
th
pull, go to next step immediately.
S
Move the choke lever to the HALF CHOKE
position.
S
Pull the starter rope sharply until the engine
runs, but no more than 5 pulls (below 30
_
F,
10 pulls). Run engine for 5 seconds, then
move choke lever to the RUN position.
S
Allow the unit to run for 30 more seconds at
the RUNposition before moving the throttle
lever to
position.
If engine has not started after 5 pulls (at HALF
CH O KE), repeat STAR TIN GA COLDENG IN E
procedure. If engine still does not start, proceed
to STAR TING A FLOOD ED ENG INE.
STARTING A WARM ENGINE
S
Move throttle lever to the
position.
S
Pull starter rope sharply until engine runs,
but no more than 5 pulls.