Poulan 952711671 Pole Saw User Manual


 
11
7. Use a screwdriver to move chain around
guide bar.
8. If chain does not rotate, it is too tight.
Slightly loosen bar clamp nut and loosen
chain by turning the adjusting screw 1/4
turn counterclockwise. Retighten bar
clamp nut.
9. If chain is too loose, it will sag below the
guide bar and needs to be tightened fol-
lowing above procedure.
WARNING: DO NOT operate the
prunerifthechainisloose. Iftheprunerisop-
erated with a loose chain, the chain could
jumpofftheguide barandresultinseriousin-
jury.
CHECK CHAIN SHARPNESS
Asharpchainmakeswoodchips.A dullchain
makes a sawdust powder and cuts slowly.
See CHAIN SHARPENING in the SERVICE
AND ADJUSTMENTS section.
BAR MAINTENANCE
If your pruner cuts to one side, has to be
forcedthroughthecut,orbeenrunwithanim-
proper amount of bar lubrication it may be
necessarytoserviceyourbar. Awornbarwill
damageyourchainandmake cuttingdifficult.
After eachuse,ensure ON/STOPswitchisin
the STOP position, then clean all sawdust
from the guide bar and sprocket hole.
To maintain guide bar:
S Move ON/STOP switch to the STOP posi-
tion and disconnect spark plug (or discon-
nect unit from power source).
S Loosen and remove bar clamp nut and
chain brake. Remove bar and chain from
pruner .
S Clean the oil holes and bar groove after
each 5 hours o f operation.
Remove Sawdust From
Guide Bar Groove
Oil Holes
S Burring of guide bar rails is a normal
process of rail wear . Remove these burrs
with a flat file.
S Whenrailtop i suneven, usea flatfile tore-
store square edges and sides.
Correct GrooveWorn Groove
File Rail Edges
and Sides
Square
Replace guide bar when the groove i s worn,
the guide bar is bent or cracked, or when
excessheatingorburringoftherailsoccurs.If
replacementis necessary,useonly theguide
bar specified for your pruner in the repair
parts list.
LUBRICATION
Bar Oil
Fill Cap
S See GUIDE BAR AND CHAIN OIL under
the OPERA TION section.
SERVICE AND ADJUSTMENTS
WARNING: Always stopunitanddis-
connect spark plug wire (or disconnect unit
from power source) be fore performing main-
tenance , se r v ice, or ad justments excep t for
carburetor adjustments.
CHAIN SH AR PENING
WARNING: Improper chain sharpen-
ing techniques and/or depth gauge m ainte-
nance will increase the chance of kickback
which can result in serious injury.
WARNING: Wear protective gloves
when handling chain. The chain is sharp and
can cut you even when it is not moving.
Conditions which indicate the need for chain
sharpening:
S Reductioninsizeofwoodchips.Thesizeof
the wood chip will decrease as the chain
getsdulleruntilitbecomesmorelikeapow-
der than a chip. Note that dead or rotted
wood will not produce a good chip.
S Saw cuts to one side or at an angle.
S Saw has to be forced through the cut.
Tools required:
S 3/16 inch (4,5 mm) diameter round file and
file holder
S Flat file
S Depth gauge tool
TO SHARPEN CHAIN:
1. MoveON/STOPswitchtotheSTOPposi-
tionanddisconnectsparkplug(ordiscon-
nect powerhead from power source).
2. Check chain for proper tension. Adjust
chain tension if necessary. See CHECK
CHAIN TENSION section.
3. Sharpen cutters.
S To sharpen the cutters, position the
fileholderlevel(90˚)sothatitrestson
the top edges of the cutter and depth
gauge.
NOTE: The chain has both left and
right hand cutters.