Filter
Top Products
10
1. Move ON/STOP switch to the ON posi-
tion.
2. Pullthechoke/fastidleleverouttothefull
extent (to the FULL CHOKE position).
3. Pull starter rope quickly with your right
handamaximumof10times. Then,pro-
ceed to the next step.
NOTE: If theenginesounds asif itis trying
to start before the10th pull, stop pulling and
immediately proceed to the next step.
4. Push the choke/fast idle lever in to the
HALF CHOKE position.
5. Pull the starter rope quickly with your
right hand until the engine starts.
6. Allowtheenginetorunforapproximately
30seconds.Then, squeezeand release
throttletriggertoallowenginetoreturnto
idle speed.
ON/STOP SWITCH
CHOKE/FAST IDLE LEVER
FULL HALF OFF
STARTING A WARM ENGINE
1. Mo veON/ S TOPswi t chtotheONposi t i o n .
2. Pull the choke/fast idle lever out to the
HALF CHOKE position.
3. Pull the starter rope quickly with your right
hand until the engine starts.
4. Squeeze and release the throttle trigger
to allow engine to return to idle speed.
DIFFICULT STARTING (or starting a
flooded engine)
The engine m ay be flooded if ithas not started
after 10 pulls.
Flooded e ngines can becleared o f excess fuel
by following the warm engine starting proce-
dure listed above. Ensure t he ON/STOP
switch is in the ON position.
Startingcouldrequire m anypulls dependingon
how badly unit is flooded. If engine still fails to
start, refer to TROUBLESHOOTING T ABLE
or call 1-800-554-6723.
CHAIN BRAKE
WARNING: Ifthebrakebandis worn
too thin it may break when the chain brake is
triggered. With abroken brake band, the chain
brake will not stop the chain. The chain brake
should be replaced by an authorized service
dealer if any part is worn to less than 0.020″
(0.5 mm) thick. Repairs on a chain brake
shouldbemade byan a uthorizedservicedeal-
er . Take your unit to the place of purchase if
purchased from a servicing dealer , or to the
nearest authorized master service dealer.
S This saw is equipped with a chain brake.
The brake is designed to stop the chain if
kickback occurs.
S The inertia--a ctivated chain brake is
activatedif thefront handguard ispushed
forward, either manually (by hand) or
automatically (by sudden movement).
S If the brake is already activated, it is
disengagedbypullingthefronthandguard
back toward the front handle as far as
possible.
S Whencuttingwiththesaw,thechainbrake
must be disengaged.
Disengaged
Engaged
Braking function control
CAUTION:
The chain brake must be
checked several times daily. The engine must
be running when performing this procedure.
This is the only instance when the saw should
be placed on the ground with the engine run-
ning.
Place the saw on f irmground. Grip the rear
handlewithyourrighthandandthefronthan-
dle with your left hand. Apply full throttle by
fully depressing thethrottle t rigger. Activate
the chain brake by turning your left wrist
against the hand guard without releasing
your grip aroundthe front handle. Thechain
should stop immediately.
Inertia activating function control
WARNING: When performing the
following procedure, the engine must be
turned off.
Grip therear handlewithyourrighthandand
thefronthandlewithyourlefthand. Holdthe
chain sawapproximately 14″(35cm) above
a stump or other wooden surface. Release
your grip on the front handle and use the
weightofthesawtoletthetipoftheguidebar
fallforwardandcontactthestump. Whenthe
tipofthebarhitsthestump,thebrakeshould
activate.