Filter
Top Products
5
KICKBACK SAFETY FEATURES
WARNING: The following features
are included on your saw to help reduce the
hazard of kickback; however, such features
will not totally eliminate this danger. As a
chainsawuser,donotrelyonlyonsafetyde-
vices. Yo u must follow all safety precau-
tions, instructions, and maintenance in this
manual to help avoid kickback and other
forces which can result in serious injury.
S Reduced--Kickback Guide Bar, designed
with a small radius tip which reduces the
size of the kickback danger zone on the
bar tip. A Reduced--Kickback Guide Bar
has beendemonstrated tosignificantly re-
duce thenumberand seriousness of kick-
backs when tested in accordance with
safety requirements for gasoline powered
chain saws as set by ANSI B175.1.
SmallRadiusTip
ReducedKickbackSymmetricalGuideBar
SymmetricalGuideBar
LargeRadiusTip
S Low--Kickback Chain, designed with a
contoured depth gauge and guard link
which deflect kickback force and allow
woodtograduallyrideintothecutter.Low--
Kickback Chain has met kickback per-
formance requirements when tested on a
representative sample of chain saws be-
low 3.8 cubic inch displacement specified
in ANSI B175.1.
Low--- Kickback
Chain
Not aLow---Kickback Chain
CanObstructMaterial
Contoured DepthGauge
Elongated GuardLink
Deflects
kickbackforce
and allowswood
to gradually ride
into cutter
S Front Hand Guard, designed to reduce the
chance ofyourlefthandcontacting thechain
if your hand slips of f the front handlebar .
S Position of front and rear handlebars, de-
signedwithdistancebetweenhandlesand
“in-line” with each other. The spread and
“in-line” position of the hands provided by
this de sign work together to give balance
and resistance in controlling the pivot of
the saw back toward the operator if kick-
back occurs.
CHAIN BRAKE A ND CKA ANGL E
S Chain Brake,designedto stopthechainin
the event of kickback.
WARNING: WE DO NOT REP-
RESENT AND YOU SHOULD NOT AS-
SUME THAT THE CHAIN BRAKE WILL
PROTEC TYOU INTHE E VEN TOF A K I CK-
BACK. K ickback is a lightning fast action
which throws the bar and rotating chain back
and up toward the operator . Kickback can be
caused by allowing contact of the bar tip in the
danger zone with any hard object. Kickback
canalsobecausedbypinchingthesawchain
along the top of the guidebar. This action may
push the guide bar rapidly back toward the op-
erator. Either of these events may cause you
to lose control of the saw which could result in
serious injury o r even death. D O NOT REL Y
UPON ANY OF T HE DEVICE S BUILT INT O
YOUR SAW. YOU SHOULD USE THESAW
PROPERL Y AND CAREFULLY TO AVOID
KICKBACK. Re duced--kickback guide bars
and low--kickback saw chains reduce the
chance and magnitude of kickback and a re
recommended. Your saw has a low kickback
chain and bar as original equipment. Repairs
on a chainbrake should b e madeby an autho-
rized servicing dealer . Take your unit to the
place of purchase if purchased from a servic-
ing dealer, or to the nearest authorized master
service dealer .
S Tipcontactinsomecasesmay cause alight-
ning fast reverse REACTION, kicking guide
bar up and back toward operator .
S Pinching the saw chain along the top of the
guide bar may push the guide bar rapidly
back toward the operator.
S Either of these reactions may cause you to
lose control of the saw which could result in
serious injury. Do not rely exclusively upon
devices built into your saw .
WARNING: C omputed kickback
angle(CKA) listedon yoursaw andlistedinthe
CKA table below represents angle of kickback
your ba r and chain combinations w ill have
when tested in accordance with CSA (Cana-
dian Standards A ssociation) and ANSI stan-
dards. When purchasing replacement bar and
chain, considerations should be given t o the
lower CKA values. Lower CKA values repre-
sent safer angles to the user , higher values in-
dicate more ang le and h igher kick energies.
Computed angles represented indicate total
energy andangleassociatedwithoutactivation
of the chain brake during kickback. Activated
anglerepresentschain stoppingtime relativeto
activation angle o f chain break a nd resulting
kick angle of saw. In all cases lower CKA val-
ues represent a safer o perating environment
for the user .
The following guid e bar and chain combina-
tions meet kickback requirements of C SA
Standards Z62.1, Z62.3, & ANSI B175.1when
used on saws listed in this manual. Use of bar
and chain combinations other than those listed
is not recommended and may not meet the
CKA requirements per standard.