Filter
Top Products
14
PRUNING
WARNING: Limit pruning to limbs
shoulder height or below . Do not cut if
branches are higher than your shoulder. Get a
professional to do the j ob.
S Makeyour first cut
1/3oftheway throughthe
bottom of the limb.
S Next make a 2nd cut a ll the way through
thelimb. Thencutathirdovercutleavinga
1to2inch(2.5to5cm)collarfromthetruck
of the tree.
First cut
Second cut
Third cut
Collar
Pruning technique
SERVICE
WARNING: Disconnect the spark
plug before performing maintenance except
for carburetor adjustments.
Werecommend allservice andadjustments
not listed in this manual be performed by an
authorized or Master Service Dealer.
HELPFUL TIP
IMPORT ANT: Have all
repairs other than the rec-
ommended maintenance
described in theinstruction
manual performed by an
authorized service dealer.
If any dealer other than an authorized
service dealer performs work on the
product, Electrolux Home Products,
Inc., may notpay for repairs under war-
ranty. Itisyourresponsibility tomaintain
and perform general maintenance.
MAINTENANCE SCHEDULE
Check:
Fuel mixture level Before each use....
Bar lubrication Before each use.......
Chain tension Before each use.......
Chain sharpness Before each use.....
For damaged parts Before each use...
For loose caps Before each use......
For loose fasteners Before each use...
For loose parts Before each use......
Inspect and Clean:
Bar Before each use................
Complete saw After each use.......
Air filter Every 5 hours*.............
Chain brake Every 5 hours*.........
Spark arresting screen
and muffler Every 25 hours*..........
Replace spark plug Yearly.
Replace fuel filter Yearly...
* Hours of Operation --
Each hour o f operation is approximately
2 tanks of fuel.
GENERAL RECOMMENDATIONS
The warranty on this unit does not cover
items that have b een subjected to operator
abuse or negligence. To receive full value
from the warranty, the operator must main-
tainunitas instructedinthis manual.V arious
adjustmentswillneedtobe madeperiodical-
ly to properly maintain your unit.
S Once ayear , replace the spark plug, airfilter,
and check guide bar and chain for wear. A
new spark plug and air filter assures proper
air-fuel mixture and helps your engine run
better and last longer .
CHECK FOR DAMAGED OR
WORN PARTS
Contact an authorized service dealer for re-
placement of damaged or worn parts.
NOTE: Itis normal forasmallamount ofoil
to appear under the saw after engine stops.
Do not confuse this with a leaking oil tank.
S ON/STOP Swi t ch -- En su re ON/STOP
switch functions properly by moving the
switch to the STOP position. Make sure en-
gine stops; then restart engine andcontinue.
S Fuel Tank -- Do not use saw if fuel tank
shows signs of damage or leaks.
S Oil Tank-- Donot usesaw ifoil tankshows
signs of damage or leaks.
CHECK FOR LOOSE
FASTENERS A ND PARTS
S Bar Nuts
S Chain
S Muffler
S Cylinder Shield
S Air Filter
S Handle Screws
S Vibration Mounts
S Starter Housing
S Front Hand Guard
CHECK CHAIN SHARPNESS
A sharp chain makes wood chips. A dull
chain makes a sawdust powder and cuts
slowly . See CH AIN SH ARPEN ING .
CHECK GUIDE BAR
Conditions which require guide bar mainte-
nance:
S Saw cuts to one side or at an angle.
S Saw has to be forced through the cut.
S Inadequate supply of oil to bar/chain.
Check t he condition of guide bar each time
chain is sharpened. A worn guide bar will
damage thechain andmake cuttingdifficult.
After each use, ensure ON/STOP switch is
inthe ST OPposition, thenclean allsawdust
from the guide bar and sprocket hole.
To maintain guide bar:
S MoveON/STOPswitchtoSTOP.
S Loosen and remove bar nuts and clutch
cover . Remove bar and chain from saw.