Filter
Top Products
16
REPLACE SPARK PLUG
The spark plug should be replaced each
year to ensure the engine starts easier and
runs better. Ignition timing is fixed and non-
adjustable.
1. Loosen 3 screws on cylinder cover.
2. Remove the cylinder cover.
3. Pull off the spark plug boot.
4. Remove spark plug from cylinder and
discard.
5. Replace with Champion RCJ--7Y spark
plug and tighten securely with a
3
/
4
inch
(19 mm) socket wrench. Spark plug gap
should be 0.025 inch (0,6 mm).
6. Reinstall the spark plug boot.
7. Reinstall the cylinder cover and 3
screws. T ighten securely.
Spark
Plug
Cylinder
Cover
Spark
Plug Boot
REPLACE FUEL FILTE R
To replace fuel filter , drain your unit by run-
ning it dry of fuel. Remove fuel cap and its
connected retainer from tank. Pull filter from
tank and remove from line. Replace and re-
assemble.
CHAIN ADJUSTMENT
See CHAIN TENSION in ASSEMBLY sec-
tion.
CHAIN SHARPENING
Chain sharpening is a complicated task and
requires special tools. We recommend that
you refer chain sharpening to a professional
chain sharpener.
CARBURETOR ADJUSTMENT
WARNING: The chain will be mov-
ing during most ofthis procedure. Wearyour
protective equipment and observe all safety
precautions. Thechain m ustnotmoveatidle
speed.
The carburetor has been carefully set a t the
factory. Adjustments may be necessary if
you notice any of the following conditions:
S Chain moves at idle. See IDLE SPEED--T
adjusting procedure.
S Saw will notidle. See IDLE SPEED--T ad-
justing procedure.
Idle Speed--T
Allow engine to idle. If the chain m oves, idle is
too f ast. If theengine stalls, idleis tooslow. Ad-
just speed until engine runs without chain
movement (idle too fast) or stalling (idle too
slow). The idle speed screw is located in the
area above the primer bulb and is labeled T.
S Turn idle screw (T) clockwise to increase
engine speed.
S Turn idle screw (T) counterclockwise t o
decrease engine speed.
If you require further assistance or are unsure
about performing this procedure, contact your
authorized service dealer or call our customer
assistance help line at 1--800--554--6723.
STORAGE
WARNING: Perform the following
steps after each use:
S Allow the engine to cool, and secure the
unit be fore storing or transporting.
S Store chain saw and fuel in a well venti-
lated area where f u elvapors cannot reach
sparks oropen flamesfrom water heaters,
electric motors or switches, furnaces, etc.
S Store chain saw with all guards in place
and position chain saw so that any sharp
object cannot accidentally cause injury .
S Store chain saw well out of the reach of
children.
SEASONAL STORAGE
Prepareyourunitfor storageattheendofthe
season or if it will not be used for 30 days or
more.
If your chain saw is to be stored f or a period
of time:
S Clean saw thoroughly before storage.
S Store i n a clean dry area.
S Lightly oil external metal surfaces and
guide bar.
S Oil the chain and wrap it inheavy paper or
cloth.
FUEL SYSTEM
Under FUELING ENGINE in the OPERA-
TION section of this manual, see message
labeled IMPORTANT regarding the use of
gasohol in your chain saw .
Fuel stabilizer is an acceptable alternative i n
minimizing the formation of fuel gum depos-
its duringstorage. Addstabilizerto the gaso-
line in the fuel t ank or fuel storage container.
Follow the m ix instructions found onstabiliz-
er containers. Run engine atleast 5 minutes
after adding stabilizer.
Poulan/Weed Eater 40:1, 2-cycle engine oil
(air cooled) is blended with fuel stabilizer. If
you d onotuse thisoil,youcan adda fuelsta-
bilizer to your fuel tank.