Filter
Top Products
16
Hub
Line in Notch
Line in Notch
Line exit holes
5. Wind the line evenly and tightly onto the
spool. Wind in the direction of the arrows
found on the spool.
6. Push the lines into the notches, leaving 3
to 5 inches (7 -- 12 cm) unwound.
7. Insert the lines into the the exit hol es in
the hub as shown in the illustration.
8. Align the notches with the line exit holes.
9. Push spool into hub until it snaps into
place.
10. Pull the lines extending outside of thehub
to release the lines from the notches.
BLADE REPLACEMENT
Refer to the ASSEMBLY section for blade re-
placement instructions and illustrations.
CARBURETOR ADJUSTMENT
WARNING:
Keep others away when
making idle speed adjustments. The trimmer
head, blade or anyoptional attachment willbe
spinning during most of this procedure. Wear
your protective equipment and observe all
safety precautions. After making adjust-
ments, the trimmer head, blade or any option-
al attachment must not move/spin at idle
speed.
The carburetor has been carefully set at the
factory. Adjustments may benecessary ifyou
notice any of the following conditions:
S
Engine will not idle when the throttle is
released.
S
The trimmer head, blade or optional
attachment moves/spins at idle.
Make adjustments with the unit supported so
the cutting attachment is off the ground and
will not make contact with any object. Hold
the unit by handwhile running and making ad-
justments. Keep all parts of your body away
from the cutting attachment and muffler .
Idle Speed Adjustment
Allow engine to i dle. Adjust speed until engine
runs without trimmer head, blade or optional
attachment moving or spinning (idle t oo fast)
or stalling (idle speed too s low).
S
Turn idle speed screw clockwise to
increase engine speed if engine stalls or
dies.
S
Turn idle speed screw counterclockwise to
decrease engine speed if trimmer head,
blade or optional attachment moves or
spins at idle.
WARNING:
Recheck the idle speed
after each adjustment. The trimmer head,
blade or optional attachment must not move
or spin at idle speed to avoid serious injury to
the operator or others.
Idle Speed
Scr e w
Air Filter
Cover
If you require further assistance orareunsure
about performing this procedure, contact an
authorized service dealer or call
1--800--554--6723.
STORAGE
WARNING:
Perform the following
steps after each use:
S
Allow engine to cool bef ore storing ortrans-
porting.
S
Store unit and fuel i n a well ventilated area
where fuel vapors cannot reach sparks or
open flames from water heaters, electric
motors or switches, furnaces, etc.
S
Store unit with all guards in place. Position
unit s o that any sharp object cannot acci-
dentally cause injury.
S
Store unit and fuel well out of the reach of
children.
SEASONAL STORAGE
Prepare unit for storage at end of season or if
it will not be used for 30 days or more.
If your unit is to be stored for a period of time:
S
Clean the entire unit before lengthy
storage.
S
Store in a clean dry area.
S
Lightly oil external metal surfaces.
FUEL SYSTEM
Under FUELING ENGINE in the OPERA-
TION section of this manual, see message l a-
beled IMPORTANT regarding the use of ga-
sohol in your engine.
Fuel s t abilizer is an acceptable alternative in
minimizing the formation of fuel gum deposits
during storage. Add stabilizer to the gasoline
in the fuel tank or fuel storage container. Fol-
low the mix instructions found on stabilizer
container. Run engine at least 5 minutes after
adding stabilizer.
ENGINE
S
Remove spark plug and pour 1teaspoon of
40:1, 2-cycleengine oil (air cooled) through
the spark plug opening. Slowly pull the
starter rope 8 to 10 times to distribute oil.
S
Replace spark plug with new one ofrecom-
mended type and heat range.
S
Clean air filter.