Filter
Top Products
-- 3 --
disconnected. Keep v ents and discharge
tubes free of debris which can accumulate
and restrict proper air flow.
D
Never place any object in the air intake open-
ing as this could restrict proper air flow and
cause damage to the unit.
D
Never use for spreading chemicals, fertiliz-
ers, orother substances which maycontain
toxic materials.
D
Toavoid spreading fire, do not use near leaf
or brush fires, fireplaces, barbecue pits,
ashtrays, etc.
D
Use only for jobs explained in this manual.
MAINTAIN YOUR UNIT PROPERLY
D
Have all maintenance other than the rec-
ommended procedures described in the in-
struction manual performed by an autho-
rized service dealer.
D
Disconnect spark plug bef or e perform ing
maintenance except for carbur etor adjust-
ments.
D
Use only recommended Poulan
r
replace-
ment parts; use of any other parts may void
your warranty and cause damage to your
unit.
D
Empty fuel t ank before storing the unit. Use
up f uelleft incarburetor bystarting engine and
letting it run until it stops .
D
Do not use any accessory or attachment
other than those r ecom mended by m anufac-
turer for use with your unit.
D
Do not store the unit or fuel in a closed area
where fuel vapors can reach sparks or an
open flame from hot water heaters, electric
motors or switches, furnaces, etc.
D
Store in a dry area out of reach of children.
SPECIAL NOTICE:
Exposure to vibra-
tions through prolonged use of gasoline pow-
ered hand tools could cause blood vessel or
nerve damage in the fingers, hands, and
joints of people prone to circulation disorders
or abnormal swelling. Prolonged use in cold
weather has been linked to blood vessel dam-
age in otherwise healthy people. If symptoms
occur such as numbness, pain, loss of
strength, change in skin color or texture, or
loss of feeling i n the fingers, hands, or joints,
discontinue the use of this t ool and seek
medical attention. An antivibration system
does not guarantee the avoidance of these
problems. Users who operate power tools on
a continual and regular basis must monitor
closely their physical condition and the condi-
tion of this tool.
SPECIAL NOTICE:
For users on U.S. For-
est Land and in some states, including Cali-
fornia (Public Resources Codes 4442 and
4443), Idaho, Maine, Minnesota, New Jersey,
Oregon, and Washington: Certain internal
combustion engines operated on forest,
brush, and/or grass covered land in the above
areas are required to be equipped with a
spark arresting screen, maintained in effec-
tive working order, or the engine must be con-
structed, equipped, and m aintained for the
prevention of fire. Check w ith your state orlo-
cal authorities for regulations pertaining to
these requirements. Failure to follow these
requirements is aviolation of t helaw. This unit
is not factory equipped with a spark arresting
screen; however, a spark arresting s creen is
available as an optional part. If a spark arrest-
ing screen is required in your area, contact
your authorized service dealer for the correct
kit. The spark arresting screen, blower tubes,
and nozzles must be assembled to unit to be
in full compliance with regulation s.
ASSEMBLY
WARNING:
Stop engine and be sure
the impeller blades have stopped turning be-
fore opening the vacuum inlet door or at-
tempting to insert or remove the vacuum or
blower tubes. The rotating blades can cause
serious injury. Always disconnect the spark
plug before performing maintenance or ac-
cessing movable parts.
WARNING:
If you receive your unit
assembled, check each step to insure your
unit is properly assembled and all fasteners
are secure. Follow all safety information in
the manual and on the unit.
D
A standard screwdriver is required for as-
sembly.
BLOWER TUBE ASSEMBLY
D
Align the rib on the blower tube with the
groove in the blower outlet; slide the tube
into place.
NOTE:
Tube clamp must beloose enough to
allow blower tube to be inserted in blower out-
let. Loosen tube clamp by turning knob coun-
terclockwise.
Blower
Tube
Blower
Outlet
Rib
Groove
D
Tighten the tube clamp by turning the knob
clockwise.
D
To remove the tube, turn the knob counter-
clockwise to loosen clamp; remove tube.
VACUUM BAG ASSEMBLY
D
Open the zipper on the vacuum bag and in-
sert the elbow tube.
D
Push the small end of the elbow tube
through the small opening in the bag.
Small
Opening
Zipper
Opening
Elbow
Tube
Rib
NOTE:
Make sure edge ofthe small opening
is f lush against the flared area of the elbow
tube, and the rib on the elbow tube is on the
bottom.