Poulan 2150 Chainsaw User Manual


 
5
Small Radius Tip
Reduced Kickback Symmetrical Guide Bar
Symmetrical Guide Bar
Large Radius Tip
S
Low--Kickback Chain, designed with a
contoured depth gauge and guard link
which deflect kickback force and allow
wood to gradually ride into the cutter. Low--
Kickback Chain has met kickback per-
formance requirements when tested on a
representative sample of chain saws be-
low 3.8 cubic inch displacement specified
in ANSI B175.1.
Low---Kickback
Chain
Not a Low---Kickback Chain
Can Obstruct Material
Contoured Depth Gauge
Elongated Guard Link
Deflects
kickback force
and allows wood
to gradually ride
into cutter
S
Front Hand Guard, designed to reduce the
chance of your left hand contacting the
chain if your hand slips off the front handle-
bar.
S
Position of front and rear handlebars, de-
signed with distance between handles and
“in-line” with each other. The spread and
“in-line” position of the hands provided by
this design work together to give balance
and resistance in controlling the pivot of
the saw back toward the operator if kick-
back occurs.
CHAIN BRAKE AND CKA ANGLE
S
Chain Brake, designed to stop the chain in
the event of kickback.
WARNING:
WE DO NOT REP-
RESENT AND YOU SHOULD NOT AS-
SUME THAT THE CHAIN BRAKE WILL
PROTECT YOU IN THE EVENT OF A
KICKBACK. Kickback is a lightning fast ac-
tion which throws the bar and rotating c hain
back and up toward the operator. Kickback
can be caused byallowing contact of the bar
tip in the danger zone with any hard object.
Kickback can also becaused by pinching the
sawchain along the topof the guide bar. This
action may push the guide bar rapidly back
toward the operator. Either of these events
may cause you to lose control of the saw
which could result in serious injury or even
death. DO NOT RELY UPON ANY OFTHE
DEVICES BUILT INTO YOUR SAW. YOU
SHOULD USE THE SAWPROPERLYAND
CAREFULLY TO AVOID KICKBACK. Re-
duced--kickback guide bars and low--kick-
back saw chains reduce the chance and
magnitude of kickback and are recom-
mended. Yoursaw has a l owkickback chain
and bar as original equipment. Repairs on a
chain brake should be made by an aut ho-
rized servicing dealer. Tak e your unit to the
place of purchase if purchased from a ser-
vicing dealer, or to the nearest authorized
master s ervice dealer.
S
Tipcontact insome c asesmaycause a l ight-
ning fast r ever se REACTION, kicking guide
bar up and back towar d operator.
S
Pinching the saw chain along the top of the
guide bar may push the guide bar rapidly
back toward the operator.
S
Either of these reactions may cause you to
lose control o f the saw which could r esult in
serious injur y. Do not rely exclusively upon
devices built into your saw.
WARNING:
Computed kickback
angle (C KA) listedon yoursaw andlisted in the
CKA table below r epr esents angle of kickback
your bar and chain combinations will have
when tested i n accordance with CSA (Cana-
dian Standards A ssociation) and ANSI stan-
dards. W hen purchasing replacement bar and
chain, consi der ations should be given to the
lower CKA values. Lower CKA values repre-
sent safer angles to the user, higher values in-
dicate more angle and higher ki ck energies.
Computed angles represented indicate total
energy andangle associated withoutactivation
of the chain b r ake during kickback. A ctivated
angle representschain stopping timerelativeto
activation angle of c hain break and resulting
kick angle of saw. I n all cases lower CKA val-
ues represent a safer operating environment
for the user.
The following guide bar and chain combina-
tions meet kickback requirements of CSA
Standards Z62.1, Z62.3, & ANSI B175.1
when used on saws listed in this manual.
Use of bar and chain combinations other
than those listed is not recommended and
may not meet the CKA requirements per
standard.
Computed kickback angle (CKA) Table
BAR
P/N
Length
CHAIN P/N
952044368 14!
LE SERIES
MODEL
CKA without chain brake
1950/2050
24
_
2025/2075/2150
2175/2350/2375
16!
18!
19
_
952051209
952051211
952051338
952044370
952044418
14
_