Filter
Top Products
NOTE: h_ the following steps, when the
choke/fast idle lever is pulled out to the full
extent, the correct throttle setting for starting
is set automatically.
ON/STOP SWITCH
(SIDE VIEW)
_ ON
STOP
1. Move ON/STOP switch to the ON posi-
tion.
2. Slowly press primer bulb 6 times
3. Pult choke/fast idle lever out to the full
extent (to the FULL CHOKE position)
4. Pulithe starter rope sharply 5 times with
your nght hand. Then, proceed to the
next step.
NOTE: If the engine sounds as if it is trying
to start before the 5th putl, stop pulling and
immediately proceed to the next step.
5. Push the choke/fast idle lever in to the
HALF CHOKE osition.
CHOKE/FA_T IDLE LEVER
o_EW)
Ch
fast idle lever OFF HALF FULL
8. Pul} the starter rope sharp}y with your
right hand until the engine starts
7. Altow the engine to run for approximate-
Iy 30 seconds Then, squeeze and re-
tease the throttle trigger to allow engine
to return to idle speed
STARTING A WARM ENGINE
1. Move ON/STOP switch to the ON posi-
tion
2. Slowly press primer bulb 6 times.
3. Puli the choke/fast idle lever out to the
HALF CHOKE position.
4-. Pull the starter rope sharply with your
right hand unfl_ the engine starts.
5. Squeeze and release throttle trigger to
allow engine to return to idle speed.
DIFFICULT STARTING (or 8tarring a
flooded engine)
The engine may be flooded with too much
fuel if it has not started after fO pulls.
Flooded engines can be cleared of excess
fuel by pushing the choke/fast idle lever in
completely (to the OFF CHOKE position)
and then following the warm engine starting
procedure listed above. Ensure the ON/
STOP sw_tch is in the ON position.
Starting could require pulling the starter rope
handle many times depending on how badly
the unit is flooded. If engine fails to start, refer
to the TROUBLESHOOTING TABLE or call
1-800-554-6723.
CHAIN BRAKE
_I, WARNING: tf the brake band is
worn too thin it may break when the chain
brake is triggered With a broken brake band,
the chain brake will not stop the chain The
chain brake should be replaced by an autho-
rized service dealer ifany part is worn to less
than O O2O" (05 mm) thick. Repairs on a
chain brake should be made by an autho-
rized service dealer Take your unit to the
place of purchase if purchased from a ser-
vicing dealer, or to the nearest authorized
master service dealer.
• This saw is equipped with a chain brake
The brake is designed to stop the chain if
kickback occurs
• The inertia-activated chain brake is
activated if the front hand guard is pushed
forward, either manually (by hand) or
automatically (by sudden movement)
• If the brake is already activated, it is
disengaged by pulling the front hand guard
back toward the front handle as far as
possible
• When cutting with the saw, the chain brake
must be disengaged
Braking function control
CAUTION: The chain brake must be
checked several times daily. The engine
must be running when performing this proce-
dure. This is the only instance when the saw
should be placed on the ground with the en-
gine runmng.
Place the saw on firm ground Grip the rear
hand}e with your right hand and the front han-
dle with your left hand. Apply full throttle by
fuily depressing the throttle trigger. Activate
the chain brake by turning your left wrist
against the hand guard without releasing
your grip around the front handle The chain
should stop immediately
Inertia activating function control
_WARNING: When performing the
following procedure, the engine must be
turned off
Grip the rear handle with your right hand and
the front handle with your left hand. Hold the
chain saw approximately 14" (35 cm) above
a stump or other wooden surface Release
your grip on the front handle and use the
weight of the saw to let the tip of the guide bar
fall forward and contact the stump. When the
tip of the bar hits the stump, the brake should
activate
10