Filter
Top Products
4
S Do not put pressure on the saw atthe endof
the cut. Applying pressure can cause you to
lose control when the cut is completed.
S Stop the engine before setting the saw
down.
S Do not operate a chain saw that is dam-
aged, improperly adjusted, or not com-
pletely and securely assembled. Always
replace bar, chain, hand guard, or chain
brakeimmediatelyifitbecomesdamaged,
broken or is otherwise removed.
S With the engine stopped, hand carry the
chain saw with the muffleraway fromyour
body , and the guide bar and chain to the
rear, preferably covered with a scabbard.
CHAIN SAW SAFETY EQUIPMENT
NOTE:
In this secti o n , the safe t y f e a t u r e s of
the chain saw and their function are explained.
For inspection and maintenance, see instruc-
tio n s i n the CHE CK ING, MAINTA I NING A ND
SERVICING CHAIN SAW SAFETY EQUIP-
MENT section. See instructions under the
WHATIS WHA T? section, tofind where these
parts are located on your chain saw . The life
span of the machine can be reduced and the
risk of accidents can increaseif machinemain-
tenance is not carried out correctly and if ser-
vice and/or repairs are not carried out profes-
sionally . If you need further information, please
contact your nearest service dealer .
S Chain brake. Your chain saw is equipped
with a chain brake that is designed tostop
the chain from moving.
WARNING: The chain brake is de-
signed to stop the chain immediately if you
geta kickback.Thechainbrakereduces the
risk of accidents, but only you can prevent
them.DONOTASSUMETHATTHECHAIN
BRAKE WILL PROTECT YOU IN THE
EVENT O F A KICKBACK.
S Throttle trigger lock--out. The throttle
lock--out is designed to prevent accidental
operation of the throttle trigger .
S Chain catcher. The chain catcher is de-
signed to catch the saw chain if it breaks.
S Vibration damping system. Your chain
saw is equipped with a vibration damping
systemthatisdes igned to minimize vibra-
tion an d make operation easier.
SAFETY NOTICE: Exposure to vibrations
through prolonged use of gasoline powered
hand tools could cause blood vessel or nerve
damageinthefingers,hands,andjoints ofpeo-
ple prone to circulation disorders or abnormal
swellings. Prolonged use in cold weather has
been linked to blood vessel damage in other-
wise healthy people. If symptoms occur such
as numbness, pain, loss ofstrength, change in
skin color or texture, or loss of feelingin thefin-
gers, hands, or joints, discontinue the use of
this tool and seek medical attention. An anti-
vibration systemdoes notguarantee theavoid-
ance of these problems. Users who operate
power tools on a continual and regular basis
must monitor closely their physical condition
and the condition of this tool.
S ON/STOP switch. The ON/STOP switch
should be used to stop the engine.
CHECKIN G, MAI N TAINING AND
SERV I CI NG CHAIN SAW SAFETY
EQUIPMENT
WARNING: Never use a chain saw
with defective safety equipment. Safety
equipment must be inspected and main-
tained. If your chain saw does not pass in-
spection, take the saw to your nearest ser-
vice dealer for repair.
S Chain brake. Brush off any wood dust,
resin and dirt from the chain brake and
clutch drum. Dirt and wear can impa irop-
eration of the brake. For additional infor-
mation, see OPERA TING YOUR UNIT
section.
S Throttletriggerlock--out. Checkthatthe
throttletriggercannotbeoperateduntilthe
throttle lock--out is pressed.
S Chain catcher. Check that the chain
catcher is not damaged and is firmly at-
tached to the body of the chain saw.
S Vibration damping system. Regularly
check the vibration damping units for
cracks or deformation. Make sure the
vibration damping units are securely at-
tached to the engine unit and handle unit.
S ON/STOP switch. Start the engine and
make sure the engine stops when you
move the ON/STOP switch to the ST OP
position.
MAINTAIN YOUR SAW IN GOOD
WORKING ORDER
S Haveallchainsawserviceperformed bya
qualifiedservice dealer with theexception
ofthe items listedinthe m aintenancesec-
tionofthismanual. Forexample,ifimprop-
ertools areusedto remove orhold thefly-
wheelwhenservicingtheclutch,structural
damage to the flywheel can occur and
cause the flywheel to burst.
S Make certain the saw chain stops moving
when the throttle trigger is released. For
correction, refer to CARBURETOR AD-
JUSTMENTS.
S Never modify your saw in any way. Use
only attachments supplied or specifically
recommended by the manufacturer.
S Keepthehandlesdry,clean, andfreeofoil
or fuel mixture.
S Keep fuel and oil caps, screws, and fas-
teners securely tightened.
S Use only Partner accessories and re-
placement parts as recommended.
HANDLE FUEL WITH CAUTION
S Do not smoke while handlingfuel or while
operating the saw.
S Eliminate all sources of sparks or flame in
the areas where fuel is mixed or poured.
Thereshouldbenosmoking,openflames,
orworkthatcouldcausesparks. Allowen-
gine to cool before refueling.
S Mix and pour fuel in an outdoor area on
bare ground; store fuel in a cool, dry , well
ventilated place; and use an approved,
marked container for all fuel purposes.
Wipe up all fuel spills before starting saw.
S Move at least 10 feet (3 meters) from fuel-
ing site before starting engine.