Filter
Top Products
PART NO.
DESCRIPTION, TYPES OF USE
91VG
Low-kickback Chamfer Chisel™ chain for cutting clean wood with electric and small gasoline chainsaws up to 2.5 cu. in. (41cc)
91VS
A professional Chamfer Chisel™ chain for experienced users of small chainsaws who prefer a low-profile 3/8”-pitch chain.
M91VS
A specialized version of 91VS with extra-heavy-duty chrome plating to cut effectively in extremely dirty, abrasive conditions.
What’s the difference between a 3/8”-pitch chain,
and a low-profile 3/8”-pitch chain?
Filing instructions, Oregon
®
91P chain
Other Oregon
®
low-profile 3/8”-pitch (91) cutting chains
FILE SIZE: Use a 5/32” round file and file guide.
TOP-PLATE
TOP-PLATE
DEPTH-GAUGE SETTING:
CUTTING ANGLE:
SIDE-PLATE ANGLE:
FILING ANGLE:
FILE-GUIDE ANGLE:
*
See warning and note below
91P Chain maintenance tools
91P Chain replacement parts
NOTE: Individual parts packages contain 25 pieces.
LEFT-HAND
RIGHT-HAND
PRESET
NOTCHED BUMPER
CHAIN TYPE
CUTTER
CUTTER
TIE STRAP
TIE STRAP
DRIVE LINK
DRIVE LINK
91P
P111807
P111808
P111616
P112320
P28298
P111822
.025”
Heel
down
85°
30°
90
°
50°
Oregon
®
91P meets the reduced-kickback requirements of ANSI B175.1 when
tested on a representative sample of chainsaws. This chain significantly reduces
the risk of chainsaw kickback while maintaining high cutting performance. ALL
CUTTING CHAIN CAN KICK BACK, WHICH MAY RESULT IN SEVERE INJURY TO
THE SAW OPERATOR OR BYSTANDERS. Users should be cautioned to operate their
saw safely, and to read and follow all warnings in their saw operator’s manual and
Oregon
®
91P chain-maintenance instructions.
Failure to follow filing instructions can
increase the level of kickback which
can result in severe injury to the saw operator or bystanders.
*
Do not exceed the depth-gauge setting shown above
*
Always file depth gauges back to their original rounded
or ramped shape after lowering
For more information on these and other Oregon
®
products, contact your authorized Oregon
®
distributor, or:
OREGON CUTTING SYSTEMS DIVISION, BLOUNT, INC.
PO Box 22127 • Portland, OR, U.S.A. 97269-2127
Phone: 503- 653-8881 Fax: 503-653-4201 http://www.oregonchain.com
IN CANADA: OREGON DISTRIBUTION LTD.
505 Edinburgh Rd. N. • Guelph, Ontario, Canada N1H 6L4
Phone: 519-822-6870 Fax: 519-822-4999 http://www.oregonchain.ca
Printed in USA PFS 91P A107038 AA 0903
WARNING
Because every
cut counts
Standard 3/8”-pitch chains are full-size professional-type chains intended for
use on medium to large gasoline-powered saws, 3.0 to 6.0 cu. in. (50-100cc).
Low-profile 3/8” chains have the same pitch, but there are differences in the
drive sprockets and bar-nose sprockets used with low-profile chains. Standard
3/8” chains and low-profile 3/8” chains are NOT interchangeable. The phrase
“low profile” refers to the height, measured from the bar’s rail to the top of the
cutter. On low-profile chains, the height is less than on standard chains. Low-
profile 3/8”-pitch chains are intended for use on electric saws, and small gasoline-powered saws up to 2.5 cubic inches (41cc).
DESCRIPTION
PACK
PART NUMBER
DESCRIPTION
PACK
PART NUMBER
Assembled File Guide, 5/32”
Each
37534
1/8” Thick Grinding Wheels (3.2mm):
Round Files, 5/32”
12-pack
70504
Full-size, 5 3/4” dia.
5-pack
OR534-18
2-pack
40459
(For use with 511A grinders)
Each
OR534-18A
Depth-gauge Tool
10-pack
22290
Mini Grinder Wheels, 4 1/8” dia.
5-pack
OR4125-18
Flat File
12-pack
12211
(For use with 108181 mini grinders)
Each
OR4125-18A
DEFINITION
3/8”-PITCH CHAIN (72V)
LOW-PROFILE 3/8”-
OF PITCH
STANDARD PROFILE
PITCH CHAIN (91P)