Filter
Top Products
4820 Red Bank Roads, Cincinnati, Ohio 45227
Printed in China, Rev. 2/02, Part No. 30280
Product specifications subject to change without notice.
3. Remove cotter pin from bolt on motor shaft. Remove nut,
washers, and bolt from motor shaft. Slide end of down rod
over plastic sleeve on motor shaft so that holes in down
rod line up with hole in motor shaft. Replace bolt, flat
washer, lockwasher, nut, and cotter pin. Bend out ends of
cotter pin to secure. Position lower canopy over motor
shaft and wiring and secure with set screw.
4. Blades may be installed at this time, or after fan is hung in
position.
PFC-48 Remove two screws and lockwashers, and steel
plate from motor housing. Leave fiber board gasket in place
on motor housing. Place blade with ribbed side up, over
gasket and replace steel plate, screws and washers. Tighten
securely. Repeat for each blade.
PFC-56 Remove two screws and lockwashers from motor
housing. Leave fiber board gasket in place on motor housing.
Place blade, with mounting bracket up, over the gasket and
replace the screws and lockwashers. Tighten securely.
Repeat for each blade.
5. Mount the fan hanger bracket to a 4" box marked for fan
support. Use the mounting screws or hardware provided
with the box. The box should be securely fastened to the
structure so that it will support at least 35 lbs. Supply
wiring, 120V, 60Hz, should be run through a wall switch to
the outlet box.
6. Place the ball hanger of the fan into the mounting bracket.
Rotate down rod until slot in ball hanger engages tab of
mounting bracket.
7. Cut off excess length of motor leads allowing 6" of lead to
extend into the outlet box. Strip leads approximately 1/4".
8. Connect fan leads to house supply wires using Listed wire
connectors. Connect white to white, black to black, and
green ground wires from fan and from mounting bracket to
the supply ground. After splice connections are made, turn
splices upward and carefully push into outlet box with
green and white leads on one side of the box and the
black leads on the other side of the box.
9. Raise the canopy up to the mounting bracket and secure
using the three screws removed earlier.
10. Restore electrical power and check for proper operation of
the fan.
IMPORTANT SAFEGUARDS
1. Be sure fan is switched off before cleaning it.
2. Keep hands, clothing and other objects away from moving
fan blades.
3. Exercise close supervision of children if they are present
when fan is operating.
4. Shut off electricity to fan before servicing or working near
fan.
5. Do not operate fan if it has been damaged in any manner.
Contact your nearest NuTone Authorized Service Center.
Two Year Limited Warranty
WARRANTY OWNER: NuTone warrants to the original consumer purchaser of its products that such products will be free from defects in materials or workmanship for a period
of two (2) years from the date of original purchase. THERE ARE NO OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
During this two year period, NuTone will, at its option, repair or replace, without charge, any product or part which is found to be defective under normal use and service.
THIS WARRANTY DOES NOT EXTEND TO FLUORESCENT LAMP STARTERS OR TUBES, FILTERS, DUCT, ROOF CAPS, WALL CAPS AND OTHER ACCESSORIES
FOR DUCTING. This warranty does not cover (a) normal maintenance and service or (b) any products or parts which have been subject to misuse, negligence, accident,
improper maintenance or repair (other than by NuTone), faulty installation or installation contrary to recommended installation instructions.
The duration of any implied warranty is limited to the one year period as specified for the express warranty. Some states do not allow limitation on how long an implied warranty
lasts, so the above limitation may not apply to you.
NUTONE’S OBLIGATION TO REPAIR OR REPLACE, AT NUTONE’S OPTION, SHALL BE THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY UNDER THIS
WARRANTY. NUTONE SHALL NOT BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES ARISING OUT OF OR IN CONNECTION WITH
PRODUCT USE OR PERFORMANCE. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may
not apply to you. This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state. This warranty supersedes all prior warranties.
WARRANTY SERVICE: To qualify for warranty service, you must (a) notify NuTone at the address stated below or telephone 1/800-543-8687, (b) give the model
number and part identification and (c) describe the nature of any defect in the product or part. At the time of requesting warranty service, you must present
evidence of the original purchase date.
Date of Installation Builder or Installer
Model No. and Product Description
IF YOU NEED ASSISTANCE OR SERVICE:
For the location of your nearest NuTone Independent Authorized Service Center:
Residents of the contiguous United States Dial Free 1-800-543-8687
Please be prepared to provide:
Product model number • Date and Proof of purchase • The nature of the difficulty
Residents of Alaska or Hawaii should write to: NuTone Inc. Attn: Department of National Field Service, 4820 Red Bank Road, Cincinnati Ohio 45227-1599.
Residents of Canada should write to: Broan-NuTone Canada, 1140 Tristar Drive, Mississauga, Ontario, Canada L5T 1H9.
Rev. 03/2001